Yamaha VX Sport Owner'S Manual Download | Manualshive

Page: 66 / 106

background image

Pre-operation checks

61

Operate the shift lever several times to make
sure that operation is smooth throughout the
whole range. Also, make sure that the reverse
gate moves up and down according to the op-
eration of the shift lever and that the gate
makes contact with the stoppers. (See page
36 for reverse system operation.)

EJU32594

Throttle lever checks

Operate the throttle lever several times to
make sure that operation is smooth through-
out the whole range. Also, make sure that the

throttle lever returns automatically to its fully
closed (idle) position when released.

Make sure that there is the proper amount of
throttle lever free play when the throttle lever
is in the fully closed (idle) position.

EJU40112

Remote control transmitter check
(VX Deluxe / VX Cruiser)

Make sure that the remote control transmitter
operates properly. (See page 31 for Yamaha
Security System setting procedures and page
37 for Low RPM Mode activation procedures.)

EJU32663

Engine shut-off cord (lanyard) check

Make sure that the engine shut-off cord (lan-
yard) is not damaged. If the cord is damaged,
replace it.

WARNING! Never try to repair

the engine shut-off cord (lanyard) or tie it

1

Stopper

1

1

Throttle lever free play

Throttle lever free play:

4.0–7.0 mm (0.16–0.28 in)

1

UF2N10E0.book Page 61 Tuesday, October 6, 2009 5:02 PM

«
...
64
65
66
67
68
...
»

Summary of Contents for VX Sport











































































































Reviews:

No comments

Related manuals for VX Sport

Brand: FARRIER MARINE Pages: 52

3372 Express Series

Brand: Cruisers Yachts Pages: 106

Brand: Sea Eagle Pages: 13

Brand: Fountaine Pajot Pages: 86

Cross 46 Side Console

Brand: YAMARIN Pages: 51

Brand: Four winns Pages: 79

Brand: Nauticstar Pages: 84

Brand: Malibu Boats Pages: 60

Brand: Malibu Boats Pages: 132

Brand: World Cat Pages: 101

INT'L VIRAGE 2000

Brand: Polaris Pages: 42

Brand: Gumotex Pages: 12

Brand: Gumotex Pages: 36

Brand: Gumotex Pages: 52

Brand: BENETEAU Pages: 138

Brand: Edgewater Networks Pages: 17

Brand: Edgewater Networks Pages: 224

380 express series

Brand: Cruisers Yachts Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands