manualshive.com logo in svg

Yamaha Viking YXM70VPXH 2016, Owner'S Manual

Share
Download
Yamaha Viking YXM70VPXH 2016 Owner'S Manual Download Page 72

6-3

6

Do not turn the key to the “

” (start) position

with the engine running; otherwise, damage
to the electric starter may result.

TIP

For maximum engine life, never accelerate
hard when the engine is cold!

 

EBU31911

Drive select lever operation and re-
verse driving

NOTICE

ECB02150

Do not shift without coming to a complete
stop and waiting for the engine to return to
normal idle speed. Damage to the engine
or drive train may occur.

 

Shifting: neutral to high and high to low

1. Stop the vehicle, and take your foot off

the accelerator pedal.

2. Apply the brake pedal, then shift by mov-

ing the drive select lever along the shift
guide. Make sure that the drive select le-
ver is completely shifted into position.

3. Release the parking brake, if applied.
4. Release the brake pedal and press the

accelerator pedal gradually.

1. Drive select lever
2. L (Low-range)
3. H (High-range)
4. N (Neutral)
5. R (Reverse)

1

2

5

4

3

UB427BE0.book  Page 3  Friday, February 5, 2016  2:14 PM

Summary of Contents for Viking YXM70VPXH 2016













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands