Yamaha VF200 Page 53 Owner'S Manual Download | Manualshive

Page: 53 / 120

background image

Engine control system

47

If the alert system has activated, stop the en-
gine as soon as it is safe to do so. Check the
oil level and add oil as needed. If the oil level
is correct and the alert device does not
switch off, consult your Yamaha dealer.

EMU43953

Water separator alert

The outboard motor is equipped with a water
separator alert system. If water separated
from the fuel exceeds a specific volume, the
alert system will activate.



The water separator-alert indicator will
come on or blink.



The buzzer will sound intermittently when
the remote control lever is in the neutral
position.

If the alert system has activated, stop the en-
gine and check the fuel filter. If any water is
found in the fuel, consult a Yamaha dealer.

NOTICE

ECM02341

Although the buzzer will stop when the

ZMU06297

ZMU07012

1. Water separator-alert indicator

1

ZMU08546

ZMU06297

ZMU07012

6CB-9-3B-1E0.book 47 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
51
52
53
54
55
...
»

Summary of Contents for VF200

























































































































Reviews:

No comments

Related manuals for VF200

Brand: Phytec Pages: 128

Brand: Sapphire Audio Pages: 50

Brand: MSI Pages: 96

Brand: Energy Pages: 14

CrossLink LIF-MD6000 Master Link Board - Revision C

Brand: Lattice Pages: 40

SUPER P4DPL-8GM

Brand: Supero Pages: 86

Brand: IEI Technology Pages: 21

Brand: PRIZM Pages: 9

STEVAL-PLC001V1

Brand: ST Pages: 42

K8T8AS - REV 3.0

Brand: JETWAY Pages: 26

Brand: Vox Technologies Pages: 36

Brand: ECS Pages: 61

Brand: EVGA Pages: 40

Brand: Wolfson Pages: 46

Brand: EVGA Pages: 2

Brand: JETWAY Pages: 55

Brand: JETWAY Pages: 47

Brand: Gigabyte Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands