Yamaha VF200 Owner'S Manual Download | Manualshive

Page: 34 / 120

background image

Components

28

EMU26191

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35



(a detent can be felt).

Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU40631

Neutral interlock trigger

The neutral interlock prevents the remote
control lever from accidentally being moved
forward or rearward from the neutral posi-
tion.
To move the remote control lever forward or
rearward from the neutral position, pull the
neutral interlock trigger up, and then move
the remote control lever.

EMU26234

Free accelerator

To open the throttle without shifting into ei-

1. Power trim and tilt switch
2. Remote control lever
3. Free accelerator button
4. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”
4. Fully closed
5. Throttle
6. Fully open

2

1

3

4

ZMU04572

ZMU07024

N

1

F

6

5

2

R

3

35˚

35˚

5

4

6

4

1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”
4. Fully closed
5. Throttle
6. Fully open

1. Neutral interlock trigger

ZMU06901

N

1

F

6

5

2

R

3

35˚

35˚

5

4

6

4

ZMU07042

1

6CB-9-3B-1E0.book 28 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
32
33
34
35
36
...
»

Summary of Contents for VF200

























































































































Reviews:

No comments

Related manuals for VF200

Brand: Abit Pages: 112

Virtex-II Pro ML300

Brand: Xilinx Pages: 17

Brand: Abit Pages: 104

Brand: AOpen Pages: 156

Brand: Elitegroup Computer Systems Pages: 82

MBD-J-JNC9VL-H81

Brand: JETWAY Pages: 43

Brand: Norco Pages: 78

Brand: QDI Pages: 20

Fatal1ty Z87 Killer Series

Brand: ASROCK Pages: 102

Brand: JETWAY Pages: 44

Brand: Gigabyte Pages: 80

975X Platinum Series

Brand: MSI Pages: 157

Brand: NXP Semiconductors Pages: 40

ADIS1650 PCBZSeries

Brand: Analog Devices Pages: 11

MT9V113PACSTCH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: JETWAY Pages: 48

Freescale MCIMX6Q-SL

Brand: NXP Semiconductors Pages: 37

Brand: Texas Instruments Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands