manualshive.com logo in svg

Yamaha V-Star 1300, Owner'S Manual

Share
Download
Yamaha V-Star 1300 Owner'S Manual Download Page 30

INSTRUMENT AND CONTROL FUNCTIONS

4-13

4

EAU14321

Helmet holder 

The helmet holder is located under the
rider seat.

To secure a helmet to the helmet
holder

1. Remove the rider seat. (See page

4-12.)

2. Attach the helmet to the helmet

holder, and then securely install
the seat. 

WARNING! Never ride

with a helmet attached to the
helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an acci-
dent.

 [EWA10161]

To release the helmet from the hel-
met holder

Remove the rider seat, remove the hel-
met from the helmet holder, and then
install the seat.

EAU42730

Sidebags 

WARNING

EWA14340

Improper loading or overloading can
cause loss of control and possibly
an accident or personal injury. See
pages 1-1 and 7-17 for important
loading and tire pressure informa-
tion.

●

Always securely close the side-
bags before riding.

●

Distribute weight evenly on
each side of the motorcycle.

●

Do not exceed the load limit of 5
kg (11 lb) for each sidebag.

●

Do not exceed the maximum
load of 190 kg (419 lb) for the ve-
hicle.

●

Do not exceed 120 km/h (80
mi/h) when riding with luggage
in the sidebags, otherwise han-
dling could be affected. Improp-
er loading, poor tire or overall
motorcycle conditions, poor
road surfaces or adverse weath-
er conditions may make it nec-
essary to further reduce the
riding speed.

1. Helmet holder

U5S612E0.book  Page 13  Wednesday, April 9, 2008  5:56 PM

Summary of Contents for V-Star 1300





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands