Yamaha V star 1100 Page 56 Owner'S Manual Download | Manualshive

Page: 56 / 407

background image

For convenience, most of the procedures listed in

Table 1

are described in this chapter. Procedures

that require more than minor disassembly or adjust-
ment are covered in the appropriate chapter in the
manual. Refer to the

Table of Contents

or

Index

to

locate a particular procedure.

CYLINDER NUMBERING

The rear cylinder is the No. 1 cylinder; the front

cylinder No. 2.

ENGINE ROTATION

Engine rotation is clockwise when viewed from

the left side. Use the flywheel nut to rotate the
crankshaft manually, and always turn the crankshaft
clockwise.

TUNE-UP

A complete tune-up restores performance that is

lost due to normal wear and deterioration. Because
engine wear occurs over a combined period of time

and

mileage,

perform

the

engine

tune-up

procedures at the intervals specified in

Table 1

.

More frequent tune-ups may be required if the mo-
torcycle is primarily operated in stop-and-go traffic.

The

Tune-Up

Specification

label

provides

tune-up specifications. This label is on the lower
frame member just beneath the left side cover (

Fig-

ure 1

). Always refer to the specifications on this la-

bel

when

servicing

the

motorcycle. If

the

specifications on the label differ from those in this
manual, use the specifications from the label.

When performing a tune-up, service the follow-

ing items as described in this chapter:
1. Air filter.
2. Spark plugs.
3. Engine compression.
4. Engine oil and filter.
5. Ignition timing.
6. Valve clearance.
7. Carburetor adjustment.
8. Brake system.
9. Suspension components.
10. Tires and wheels.
11. Fasteners.

Air Filter Replacement

The air filter removes dust and abrasive particles

from the incoming air before it enters the carbure-
tors and the engine. Without an air filter, very fine
particles could enter the engine and rapidly wear the
piston rings, cylinders and bearings. These particles
could also clog small passages in the carburetors.
Never run the motorcycle without the air filter ele-
ment installed.

The air filter is a dry-element type; no oiling is re-

quired. Proper air filter servicing can do more to en-
sure long service from your engine than almost any
other single item. Remove and clean the air filter el-
ement at the interval listed in

Table 1

. Replace the

air filter if it is soiled, severely clogged or broken in
any area.
1. Make sure the ignition switch is off.
2. Securely support the motorcycle on level
ground.
3. Remove the cover screws (A,

Figure 2

), and re-

move the air filter cover (B).
4. Remove the air filter element from the posts
(

Figure 3

) on the housing.

LUBRICATION, MAINTENANCE AND TUNE-UP

57

3

1

2

«
...
54
55
56
57
58
...
»

Summary of Contents for V star 1100
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for V star 1100

Brand: Cannondale Pages: 61

Brand: hepco & becker Pages: 6

Brand: Honda Pages: 141

Brand: Fantic Motor Pages: 145

Brand: Takegawa Pages: 2

6513515 00 22-00-40

Brand: hepco & becker Pages: 7

Brand: KTM Pages: 26

Brand: Androware Pages: 2

Brand: Miller Pages: 22

B-TRK502-01-01-SL

Brand: SRC Pages: 5

Brand: DYNATEK Pages: 1

Brand: DYNATEK Pages: 2

Brand: Husqvarna Pages: 7

Brand: Shad Pages: 2

Brand: Shad Pages: 2

TOPMASTER V0NR55ST

Brand: Shad Pages: 2

TOPMASTER Y0TM52ST

Brand: Shad Pages: 3

Brand: Shad Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands