manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 23

 

INSTRUMENT AND CONTROL FUNCTIONS

 

4-5

 

2

3

4

5

6

7

8

9

 

EAU12941

 

Brake pedal 

 

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

 

EAU32281

 

Fuel tank cap 

 

To remove the fuel tank cap

 

1. Insert the key into the lock and turn

it 1/3 turn counterclockwise.

2. Turn the fuel tank cap 1/3 turn

counterclockwise and pull it off.

 

To install the fuel tank cap

 

1. Insert the fuel tank cap into the tank

opening with the key inserted in the
lock, and then turn the cap 1/3 turn
clockwise.

2. Turn the key 1/3 turn clockwise,

and then remove it.

TIP

 

The fuel tank cap cannot be installed
unless the key is in the lock. In addition,
the key cannot be removed if the cap is

 

not properly installed and locked.

WARNING

 

EWA10121

 

Make sure that the fuel tank cap is
properly closed and locked before

 

riding. Leaking fuel is a fire hazard.

 

1. Brake pedal

1

 

1. Fuel tank cap

2. Unlock.

1

2

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands