Yamaha TS-S User Manual Download Page 215 | Manualshive

Page: 215 / 286

background image

A

ht

1

o

peration Guide

A-27

6.2 Origin search (return-to-origin)

To find the robot origin position, use the following procedure after making sure that the servo is on.

n

NOTE

Origin search cannot be performed unless the
servo is on.

w

WARNING

thE RoBot WIll NoW MovE, So uSE CAutIoN.

1

On the main menu screen, select

"Operation".

The "Operation" menu screen appears
showing selectable menu items.

2

Move the cursor to "Origin Search"

and press

.

The "Origin Search" screen appears showing
the origin search method and direction.

NRM

[01]

Servo status

Origin search

Run

Reset

Current pos.

128.00 mm

Operation

Method: TORQUE
Direction: CCW
Coordinates:Normal

RUN:Origin search start
Current pos.

128.00 mm

Origin search

NRM

[01]

"Origin Search" screen

Step 2

24A31-M0-00

3

Ensure safety and press

RUN

to start

an origin search.

The message "Running…" appears during
origin search.
If you want to stop the origin search, press

STOP

.

Method: TORQUE
Direction: CCW
Coordinates:--

RUN:Origin search start
Current pos.

128.00 mm

Origin search

NRM

[01]

Origin search

Running…

Origin search (return-to-origin) running screen

Step 3

24A32-M0-00

4

When origin search is complete,

check the message.

The message "OK" and machine reference
(Ref. = ** %) appear when the origin search
has ended successfully.

Method: TORQUE
Direction: CCW
Coordinates:

RUN:Origin search start
Current pos.

128.00 mm

Origin search

NRM

[01]

Origin search

OK

Ref. = 50 %

Origin search (return-to-origin) completion screen

Step 4

24A33-M0-00

n

NOTE

The machine reference must be adjusted if it is
outside an allowable range of 25% to 75%
(allowable range may differ depending on the
robot type, so refer to the robot user's manual).
For information on how to adjust the machine
reference, contact our sales office or
representative.

5

Press

CLR

.

This returns to the "Origin Search" screen.
Pressing

CLR

once more returns to the

"Operation" menu screen.

«
...
213
214
215
216
217
...
»

Summary of Contents for TS-S































































































































































































































































































Reviews:

No comments

Related manuals for TS-S

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

Brand: Eaton Pages: 12

Brand: Eaton Pages: 100

Brand: FAAC Pages: 32

Brand: IDTECK Pages: 94

Brand: Ziton Pages: 36

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brand: H-Tronic Pages: 32

Brand: Ban Seok Pages: 9

ZITON RADIO LOOP MODULE

Brand: EMS Pages: 26

Brand: Danfoss Pages: 30

Brand: Decagon Pages: 27

Brand: Frico Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands