PERIODIC MAINTENANCE
3-21
EAS30652
CHECKING THE SIDESTAND SWITCH
Refer to “CHECKING THE SWITCHES” on
page 8-129.
EAS30653
CHECKING THE FRONT FORK
1. Stand the vehicle on a level surface.
WARNING
EWA13120
Securely support the vehicle so that there is
no danger of it falling over.
2. Check:
• Inner tube
Damage/scratches
→
Replace.
• Front fork leg
Oil leaks between inner tube and outer tube
→
Replace the oil seal.
3. Hold the vehicle upright and apply the front
brake.
4. Check:
• Front fork operation
Push down hard on the handlebar several
times and check if the front fork rebounds
smoothly.
Rough movement
→
Repair.
Refer to “FRONT FORK” on page 4-58.
EAS30806
ADJUSTING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
WARNING
EWA13120
Securely support the vehicle so that there is
no danger of it falling over.
Rebound damping
NOTICE
ECA13590
Never go beyond the maximum or minimum
adjustment positions.
1. Adjust:
• Rebound damping
a. Turn the adjusting screw “1” in direction
“a” or “b”.
TIP
Although the total number of clicks of a damping
force adjusting mechanism may not exactly
match the above specifications due to small dif-
ferences in production, the actual number of
clicks always represents the entire adjusting
range. To obtain a precise adjustment, it would
be advisable to check the number of clicks of
each damping force adjusting mechanism and
to modify the specifications as necessary.
Compression damping
NOTICE
ECA13590
Never go beyond the maximum or minimum
adjustment positions.
TIP
Before adjusting the compression damping, re-
move the rubber cap.
1. Adjust:
• Compression damping
a. Turn the adjusting screw “1” in direction
“a” or “b”.
Direction “a”
Rebound damping is increased (sus-
pension is harder).
Direction “b”
Rebound damping is decreased (sus-
pension is softer).
Rebound damping
Adjustment value from the start
position (Soft)
31
Adjustment value from the start
position (STD)
17
Adjustment value from the start
position (Hard)
0
* With the adjusting screw fully turned in
direction “a”
1
b
a
Summary of Contents for Tenere 700 2020
