background image

SWP2 Owner’s Manual

3

1.  IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions 
contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your 
authority, granted by the FCC, to use the product.

2.  IMPORTANT: 

When connecting this product to accessories 

and/or another product use only high quality shielded cables. 
Cable/s supplied with this product MUST be used. Follow all 
installation instructions. Failure to follow instructions could 
void your FCC authorization to use this product in the USA.

3.  NOTE: 

This product has been tested and found to comply 

with the requirements listed in FCC Regulations, Part 15 for 
Class “A” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your use 
of this product, in a commercial environment, will not result in 
harmful interference with other electronic devices. However, 
operation of this product in a residential area is likely to cause 
interference in some form. In this case you, the user, bear the 
responsibility of correcting this condition.
This product generates/uses radio frequencies and, if not 
installed and used according to the instructions found in the 
users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regula-
tions does not guarantee that interference will not occur in all 
installations. If this product is found to be the source of inter-
ference, which can be determined by turning the product 
“OFF” and “ON”, please try to eliminate the problem by using 
one of the following measures:
Relocate either the product generating the interference or the 
device that is being affected by the interference. 
Utilize power outlets that are on different branch (circuit 
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the 
antenna. If the antenna lead-in is 300 ohm ribbon lead, 
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory 
results, please contact the local retailer that is authorized to 
distribute this type of product. If you can not locate the appro-
priate retailer, please contact Yamaha Corporation of Amer-
ica, Electronic Service Division, 6600 Orangethorpe Ave, 
Buena Park, CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.

(class A)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Ave. Buena Park CA 90620

Telephone: 714-522-9011

Type of Equipment: L2 Switch

Model Name: SWP2-10MMF, SWP2-10SMF

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference 

that may cause undesired operation.

Summary of Contents for SWP2























Reviews: