Yamaha STRATOLINER XV19CTSV Owner'S Manual Download Page 75

Page: 75 / 100

PERIODIC MAINTENANCE AND MINOR REPAIR

6-28

EAU39121

Replacing a headlight bulb

This model features a headlight
equipped with two quartz bulbs. If the
high beam or the low beam bulb burns
out, replace it as follows.

Removing the headlight unit

1. Remove the windshield. (See

page 3-15.)

2. Remove the main switch/steering

lock cover by removing the bolts.

3. Disconnect the coupler shown.

4. Remove the headlight unit by re-

moving the screws.

To replace the high beam headlight
bulb

1. Remove the headlight bulb holder

cover by turning it counterclock-
wise.

1. Low beam headlight bulb

2. High beam headlight bulb

1. Bolt
2. Main switch/steering lock cover

1. Coupler

1. Screw

1. Headlight bulb holder cover

U2C510E0.book Page 28 Monday, September 12, 2005 1:17 PM

Summary of Contents for STRATOLINER XV19CTSV





































































































Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands

Yamaha STRATOLINER XV19CTSV, Owner'S Manual

Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands