Yamaha STRATOLINER XV19CTSV Owner'S Manual Download Page 30

Page: 30 / 100

INSTRUMENT AND CONTROL FUNCTIONS

3-13

EAU39153

Passenger backrest

To remove the backrest

1. Open the sidebag lids. (See page

3-17.)

2. Insert the key into the passenger

backrest lock, turn it counterclock-
wise, and then remove the key.

3. Pull the lever on each side of the

backrest upward.

4. While holding the levers in the up-

ward position, lift the backrest up-
ward and remove it by pulling it to
the rear.

To install the backrest

1. Fit the slot on each backrest brack-

et (left and right side) into the
groove of its holder.

CAUTION:

ECA15371

Be careful not to scratch the fender
when fitting the slot into the groove.

2. Push the rear of the backrest down

smoothly but forcefully to lock it in
place and make sure that the lever
hook on each side is securely fit
over its holder.

1. Key

2. Unlock.

1. Backrest lever
2. Passenger backrest

1. Slot
2. Holder

U2C510E0.book Page 13 Monday, September 12, 2005 1:17 PM

Summary of Contents for STRATOLINER XV19CTSV





































































































Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands

Yamaha STRATOLINER XV19CTSV, Owner'S Manual

Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands