Yamaha Star XVS13CAC Owner'S Manual Download

Page: 64 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-23

EAU23040

Drive belt slack

The drive belt slack should be checked
and adjusted at the intervals specified
in the periodic maintenance and lubri-
cation chart.

EAU38410

To check the drive belt slack

1. Place the vehicle on the sidestand.
2. Note the current position of the

drive belt using the marks near the
drive belt check hole.

TIP

The marks near the drive belt check
hole are 5.0 mm (0.2 in) apart.

3. Note the position of the drive belt

with a force of 45 N (4.5 kgf, 10 lbf)
applied to the belt with a belt ten-
sion gauge as shown.

TIP

A belt tension gauge is available at a
Yamaha dealer.

4. Calculate the drive belt slack by

subtracting the measurement not-
ed in step 2 from the measurement
noted in step 3.

5. If the drive belt slack is incorrect,

have a Yamaha dealer adjust it.

1. Drive belt
2. Marks

1. Belt tension gauge

2. Drive belt slack

Drive belt slack:

5.0–7.0 mm (0.20–0.28 in)

U27D10E0.book Page 23 Thursday, July 22, 2010 1:05 PM

Summary of Contents for Star XVS13CAC



































































































Search results

Summary of Contents for Star XVS13CAC

Reviews:

Related manuals for Star XVS13CAC

Brands by name

Popular brands

Yamaha Star XVS13CAC, Owner'S Manual

Search results

Summary of Contents for Star XVS13CAC

Reviews:

Related manuals for Star XVS13CAC

Brands by name

Popular brands