background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-10

7

EAU19681

Canister (for California only) 

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

Check each hose connection.

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

EAU42102

Engine oil and oil filter ele-
ment 

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the periodic maintenance and lubri-
cation chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles, and then check the oil level
through the check window located
at the bottom-right side of the
crankcase.

TIP

The engine oil should be between the
minimum and maximum level marks.

1. Canister cover
2. Canister breather

3. Canister

U46B10E0.book  Page 10  Tuesday, May 20, 2008  7:32 PM

Summary of Contents for Star XV250Y































































































Reviews: