Yamaha Star XV19MY Owner'S Manual Download | Manualshive

Page: 37 / 94

background image

FOR YOUR SAFETY – PRE-OPERATION CHECKS

5-2

5

EAU15605

Pre-operation check list

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.

Engine oil

• Check oil level in oil tank.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

Transfer case oil

• Check vehicle for oil leakage.

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Rear brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Clutch

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check fluid level in reservoir.
• If necessary, add recommended fluid to specified level.
• Check hydraulic system for leakage.

Throttle grip

• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

U1D713E0.book Page 2 Thursday, May 8, 2008 4:19 PM

«
...
35
36
37
38
39
...
»

Summary of Contents for Star XV19MY































































































Reviews:

No comments

Related manuals for Star XV19MY

Brand: HYOSUNG Pages: 199

Brand: LAMAX Pages: 134

TXT PRO - PART LIST 2010

Brand: GAS GAS Pages: 64

Brand: NZI Helmets Pages: 4

Brand: Honda Pages: 190

Daytona 955i 2002

Brand: Triumph Pages: 384

Freeride 350 2013

Brand: KTM Pages: 113

Brand: Abus Pages: 18

Brand: Yamaha Pages: 287

Brand: Yamaha Pages: 109

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 124

ROAD STAR XV16A

Brand: Yamaha Pages: 117

X MAX CZD300P 2022

Brand: Yamaha Pages: 142

Brand: Yamaha Pages: 97

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands