Yamaha Star XV19MY Owner'S Manual Download | Manualshive

Page: 30 / 94

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-14

4

EAU38342

Helmet holder

The helmet holder is located under the
rider seat. A helmet holding cable is
provided beside the owner’s tool kit to
secure a helmet to the helmet holder.

To secure a helmet to the helmet
holder

1. Remove the rider seat. (See page

2. Pass the helmet holding cable

through the buckle on the helmet
strap as shown, and then hook the
cable loop over the helmet holder.

3. Place the helmet on the left side of

the vehicle, and then install the rid-
er seat.

WARNING! Never ride

with a helmet attached to the
helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an acci-
dent.

[EWA10161]

NOTICE:

Be sure to

place the helmet on the left side
of the vehicle. Some helmets
may contact the muffler when
placed on the right side be-
cause of their size or shape.

[ECA15331]

To release the helmet from the hel-
met holder

Remove the rider seat, remove the hel-
met holding cable from the helmet hold-
er and the helmet, and then install the
seat.

1. Helmet holder

2. Helmet holding cable

1. Helmet holding cable
2. Helmet

U1D713E0.book Page 14 Thursday, May 8, 2008 4:19 PM

«
...
28
29
30
31
32
...
»

Summary of Contents for Star XV19MY































































































Reviews:

No comments

Related manuals for Star XV19MY

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 44

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: kellermann Pages: 2

Brand: BMW Motorrad Pages: 146

Bonneville T100

Brand: Triumph Pages: 198

Brand: PUIG Pages: 2

Brand: KTM Pages: 7

Brand: Race Dynamics Pages: 25

Brand: Suzuki Pages: 24

Brand: Suzuki Pages: 31

Brand: Suzuki Pages: 74

Brand: Suzuki Pages: 37

Brand: Suzuki Pages: 125

Brand: Suzuki Pages: 353

Brand: Suzuki Pages: 355

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands