Yamaha STAR XV19CSX Owner'S Manual Download

Page: 71 / 96

PERIODIC MAINTENANCE AND MINOR REPAIR

6-30

5. Install the headlight bulb cover,

and then connect the coupler.

6. Install the headlight unit by install-

ing the screws.

7. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24180

Tail/brake light

This model is equipped with an LED
type of tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

EAU24210

Replacing a turn signal light
bulb

1. Remove the turn signal lens by re-

moving the screws.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

CAUTION:

ECA10680

Do not overtighten the screws, oth-
erwise the lens may break.

1. Do not touch the glass part of the bulb.

1. Screw

U29S10E0.book Page 30 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands