Yamaha STAR XV19CSX Owner'S Manual Download

Page: 68 / 96

PERIODIC MAINTENANCE AND MINOR REPAIR

6-27

sealed-type (MF) battery charg-
er, have a Yamaha dealer
charge your battery.

EAU42582

Replacing the fuses

The main fuse, the fuel injection system
fuse, and the fuse box, which contains
the fuses for the individual circuits, are
located under the rider seat. (See page
3-11.)
If a fuse is blown, replace it as follows.

1. Unhook the battery band, and then

remove the battery cover.

2. Turn the key to “OFF” and turn off

the electrical circuit in question.

3. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

1. Battery band

2. Battery cover

1. Main fuse
2. Fuel injection system fuse

3. Fuel injection system spare fuse

4. Fuse box

U29S10E0.book Page 27 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands