Yamaha STAR XV19CSX Owner'S Manual Download

Page: 34 / 96

INSTRUMENT AND CONTROL FUNCTIONS

3-17

EAU44582

Auxiliary DC connector

To access the auxiliary DC connec-
tor

1. Remove the rider seat. (See page

3-11.)

2. Unhook the battery band, and then

remove the battery cover.

3. Turn the ECU (Electronic Control

Unit) over to move it away from the
wire harness protective cover as
shown.

4. Open the wire harness protective

cover.

A 12-V accessory connected to the
auxiliary DC connector under the rider
seat can be used when the key is in the
“ON” position.

CAUTION:

ECA15310

The accessory connected to the
auxiliary DC connector should not
be used with the engine turned off,
and the load must never exceed 36
W (3 A), otherwise the battery may
discharge.

WARNING

EWA12531

To prevent electrical shock or short-
circuiting, make sure that the cap is
installed when the auxiliary DC con-
nector is not being used.

1. Battery band

2. Battery cover

1. Wire harness protective cover
2. ECU (Electronic Control Unit)

1. Auxiliary DC connector

U29S10E0.book Page 17 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands