manualshive.com logo in svg

Yamaha STAR XV19CSX, Owner'S Manual, Page: 31 / 96

Share
Download
Yamaha STAR XV19CSX Owner'S Manual Download Page 31

INSTRUMENT AND CONTROL FUNCTIONS

3-14

3

CAUTION:

ECA10120

Always tighten the locknut against
the adjusting nut, and then tighten
the locknut to the specified torque.

WARNING

EWA10220

This shock absorber contains highly
pressurized nitrogen gas. For prop-
er handling, read and understand
the following information before
handling the shock absorber. The
manufacturer cannot be held re-
sponsible for property damage or
personal injury that may result from
improper handling.

●

Do not tamper with or attempt to
open the gas cylinder.

●

Do not subject the shock ab-
sorber to an open flame or other
high heat sources, otherwise it
may explode due to excessive
gas pressure.

●

Do not deform or damage the
gas cylinder in any way, as this
will result in poor damping per-
formance.

●

Always have a Yamaha dealer
service the shock absorber.

EAU15281

EXUP system 

This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve)
system. This system boosts engine
power by means of a valve that regu-
lates the diameter of the exhaust pipe.
The EXUP system valve is constantly
adjusted in accordance with the engine
speed by a computer-controlled servo-
motor.

CAUTION:

ECA10191

●

The EXUP system has been set
and extensively tested at the
Yamaha factory. Changing
these settings without sufficient
technical knowledge may result
in poor performance of or dam-
age to the engine.

●

If the EXUP system cannot be
heard when the main switch is
turned on, have a Yamaha deal-
er check it.

U29S10E0.book  Page 14  Friday, May 18, 2007  1:53 PM

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments