Yamaha STAR XV19CSX Owner'S Manual Download

Page: 29 / 96

INSTRUMENT AND CONTROL FUNCTIONS

3-12

EAU44440

Helmet holder

The helmet holder is located under the
rider seat. A helmet holding cable is
provided under the rider seat to secure
a helmet to the helmet holder.

To secure a helmet to the helmet
holder

1. Remove the rider seat. (See page

3-11.)

2. Pass the helmet holding cable

through the buckle on the helmet
strap as shown, and then hook the
cable loop over the helmet holder.

3. Place the helmet on the left side of

the vehicle, and then install the rid-
er seat.

CAUTION:

ECA15330

Be sure to place the helmet on the
left side of the vehicle. Some hel-
mets may contact the muffler when
placed on the right side because of
their size or shape.

WARNING

EWA10160

Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of con-
trol and possibly an accident.

To release the helmet from the hel-
met holder

Remove the rider seat, remove the hel-
met holding cable from the helmet hold-
er and the helmet, and then install the
seat.

1. Helmet holding cable

2. Helmet holder

1. Helmet holding cable
2. Helmet

U29S10E0.book Page 12 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands