Yamaha Star 2010 Owner'S Manual Download | Manualshive

Page: 93 / 104

background image

CONSUMER INFORMATION

10-4

10

EAU26560

Motorcycle noise regulation

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:

Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-
hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.

Exhaust system

• Muffler
• Exhaust pipe
• Silencer

Intake system

• Air cleaner case
• Air cleaner element
• Intake duct

U5S614E0.book Page 4 Friday, July 9, 2010 9:18 AM

«
...
91
92
93
94
95
...
»

Summary of Contents for Star 2010









































































































Reviews:

No comments

Related manuals for Star 2010

Brand: Honda Pages: 112

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

Brand: KYMCO Pages: 69

Brand: Suzuki Pages: 311

Brand: KTM Power Parts Pages: 22

Brand: Bajaj Pages: 39

Brand: PUIG Pages: 2

Brand: hepco & becker Pages: 2

Brand: Kobalt Pages: 33

Brand: KOOFU Pages: 24

Brand: Taurus Pages: 48

Brand: Piaa Pages: 17

Brand: Yamaha Pages: 91

Brand: Yamaha Pages: 117

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 132

XV 535 DX Virago

Brand: Yamaha Pages: 211

Brand: Yamaha Pages: 211

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands