background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-11

7

TIP

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.

3. Install the spark plug cap.
4. Install the spark plug cover by in-

stalling the bolts.

EAU19681

Canister (for California only) 

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the fol-
lowing:

Check each hose connection.

Check each hose and canister for
cracks or damage. Replace if dam-
aged.

Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.

EAU42599

Engine oil and oil filter car-
tridge 

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.

To check the engine oil level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Wait a few minutes until the oil set-

tles, and then check the oil level
through the engine oil level check
window located at the bottom-left
side of the crankcase.

TIP

The engine oil should be between the
minimum and maximum level marks.

U5S614E0.book  Page 11  Friday, July 9, 2010  9:18 AM

Summary of Contents for Star 2010









































































































Reviews: