Yamaha S-03SL, Owner'S Manual

Page: 82 / 112

82
V
oice Mode
29-1. Lvl Ofs1 (Level Offset 1)
29-2. Lvl Ofs2 (Level Offset 2)
29-3. Lvl Ofs3 (Level Offset 3)
29-4. Lvl Ofs4 (Level Offset 4)
Set the Amplitude Scaling Offset Levels. These Offsets
are used by the Break Points (BP1/BP2/BP3/BP4).
n
Details about Amplitude Scaling are given later in the
section “Amplitude Scaling Settings” below.
❏
Settings: Lvl Ofs1~Lvl Ofs4:–128~+127
Amplitude Scaling Settings
By way of example, you could set the Levels (Offsets)
and Break Points (BP1 to 4) as follows.
Here, the current amplitude is 80. The Offsets are
–4 at BP1 (set to note E1), +10 at BP2 (set to note
B2), +17 at BP3 (set to note G4) and +4 at BP4 (set
to A5). That is, the amplitudes at each Break Point
are 76, 90, 97 and 84, respectively. For other notes,
the amplitudes will be on the straight line
connecting the two adjacent Break Points.
n
The Break Point Levels are Offsets used to increase
or decrease the current amplitude at the specified
notes. Regardless of the size of these Offsets, the
minimum and maximum amplitude limits (values
of 0 and 127, respectively) cannot be exceeded.
n
A note set below the BP1 will become the BP1
Level. A note set above BP4 will become the BP4
Level.
30. LvlSclSens
(Level Scale Sensitivity)
Determines the Time Scale (how fast the volume
changes across the range of the keyboard) for each
Element. The higher the value, the slower the change
for lower notes and the faster the change for higher
notes.
❏
Settings: 0~15
31. KeyonDelay
Determines the time (delay) between the moment you
press a note on the keyboard and the point at which the
sound is played. You can set different delay times for
each Element.
❏
Settings: 0~15
32-1. LFO Wave
32-2. LFO Phase
(LFO Phase Initialize)
There are various settings for the LFO. The LFO is
used to generate low frequency signals and can be used
to create vibrato, wah, tremolo and other effects when
applied to pitch/filter/amplitude/etc. parameters. For
example, it can be applied simultaneously to both pitch
and filter, or to specific parameters of individual
Elements.
■
LFO Wave
Determines the LFO Wave. Depending on the Wave
selected, you can create different kinds of modulated
sounds. The following three LFO waveforms are
available.
❏
Settings: saw, tri, S&H
n
S&H = Adds random changes to the pitch. Tri
(Triangle) waves will be applied for the LFO AMod
and LFO FMod. Triangle wave is applied even if you
select S&H for LFO PMod, when controlling the LFO
PMod with the Modulation Wheel.
Lvl Ofs1
KEY ELEM PART
OCTAVE
PAGE
+000
29 E 1
Lvl Ofs2
KEY ELEM PART
OCTAVE
PAGE
+000
29 E 1
Lvl Ofs3
KEY ELEM PART
OCTAVE
PAGE
+000
29 E 1
Lvl Ofs4
KEY ELEM PART
OCTAVE
PAGE
+000
29 E 1
1 2 3 4
E1 B2 G4 A5
–4
BP
Ofs +10 +17 +4
LvlSclSens
KEY ELEM PART
OCTAVE
PAGE
00
30 E 1
KeyonDelay
KEY ELEM PART
OCTAVE
PAGE
00
31 E 1
LFO Phase
KEY ELEM PART
OCTAVE
PAGE
on
32 E 1
LFO Wave
KEY ELEM PART
OCTAVE
PAGE
tri
32 E 1
Element Amplitude/Element LFO