Yamaha RX-V379 Owner'S Manual Download Page 75

Page: 75 / 78

• Maximum Effective Output Power (1-channel driven)

[U.S.A. and Canada models] (1 kHz, 10% THD, 8

)

Front L/R, Center, Surround L/R................................ 130 W/ch

[Other models] (1 kHz, 10% THD, 6

)

Front L/R, Center, Surround L/R................................ 135 W/ch

• Dynamic Power (1-channel driven) (IHF)

[U.S.A. and Canada models]

Front L/R (8/6/4/2

) .................................. 110/130/160/180 W

[Other models]

Front L/R (6/4/2

) ............................................ 110/130/150 W

• Damping Factor

Front L/R, 20 Hz to 20 kHz, 8

............................. 100 or more

• Input Sensitivity / Input Impedance

AV 2 etc. (1 kHz, 100 W/6

)..............................200 mV/47 k

• Maximum Input Signal

AV 2 etc. (1 kHz, 0.5% THD, Effect On) ........................... 2.3 V

• Output Level / Output Impedance

SUBWOOFER ...........................................................1 V/1.2 k

• Headphone Jack Rated Output / Impedance

AV 2 etc. (1 kHz, 50 mV, 8

) .............................100 mV/470

• Frequency Response

AV 2 etc. to Front (10 Hz to 100 kHz) ......................... +0/-3 dB

• Signal to Noise Ratio (IHF-A Network)

AV 2 etc. (Input 1 k

Shorted, Speaker Out)

..........................................................................110 dB or more

• Residual Noise (IHF-A Network)

Front L/R (Speaker Out)......................................150 µV or less

• Channel Separation

AV 2 etc. (Input 1 k

Shorted, 1 kHz/10 kHz)

................................................................. 70 dB/50 dB or more

• Volume Control

Range ............................................. MUTE, -80 dB to +16.5 dB

Step ................................................................................ 0.5 dB

• Tone Control Characteristics (Front L/R)

Bass Boost/Cut............................. ±6 dB/0.5 dB Step at 50 Hz

Bass Turnover ............................................................... 350 Hz

Treble Boost/Cut..........................±6 dB/0.5 dB Step at 20 kHz

Treble Turnover..............................................................3.5 kHz

• Filter Characteristics

(fc=40/60/80/90/100/110/120/160/200 Hz)

H.P.F. (Front, Center, Surround)................................ 12 dB/oct.

L.P.F. (Subwoofer)..................................................... 24 dB/oct.

Video Section

• Video Signal Type

[U.S.A., Canada, Korea, Taiwan and General models].. NTSC

[Other models] .................................................................. PAL

• Video Signal Level

Composite ............................................................. 1 Vp-p/75

• Video Maximum Input Level (Video Conversion Off)

.......................................................................1.5 Vp-p or more

• Video Signal to Noise Ratio ................................ 50 dB or more

FM Section

• Tuning Range

[U.S.A. and Canada models] .............. 87.5 MHz to 107.9 MHz

[Asia, Taiwan and General models]

...................................... 87.5/87.50 MHz to 108.0/108.00 MHz

[Other models] ................................ 87.50 MHz to 108.00 MHz

• 50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.)

Mono .................................................................2 µV (17.3 dBf)

• Signal to Noise Ratio (IHF)

Mono ............................................................................... 71 dB

Stereo .............................................................................. 70 dB

• Harmonic Distortion (IHF, 1 kHz)

Mono .................................................................................0.5%

Stereo ................................................................................0.6%

• Antenna Input................................................ 75

unbalanced

AM section

• Tuning Range

[U.S.A. and Canada models]...................530 kHz to 1710 kHz

[Asia, Taiwan and General models]

.................................................530/531 kHz to 1710/1611 kHz

[Other models] .........................................531 kHz to 1611 kHz

General

• Power Supply

[U.S.A. and Canada models].......................... AC 120 V, 60 Hz

[Taiwan and General models]

...................................... AC 110 to 120/220 to 240 V, 50/60 Hz

[Korea model] ................................................. AC 220 V, 60 Hz

[Australia model]............................................. AC 240 V, 50 Hz

[U.K. and Europe models] .............................. AC 230 V, 50 Hz

[Asia model].................................... AC 220 to 240 V, 50/60 Hz

• Power Consumption........................................................ 260 W

• Standby Power Consumption

HDMI Control Off

[Taiwan and General models] .......................................... 0.5 W

[Other models] ................................................................. 0.3 W

HDMI Control On (No Signals)......................................... 0.9 W

• Maximum Power Consumption

[Taiwan and General models] ......................................... 470 W

• Dimensions (W x H x D)

............................ 435 x 151 x 315 mm (17-1/8” x 6” x 12-3/8”)

* Including legs and protrusions

• Weight ............................................................. 7.4 kg (16.3 lbs)

* Specifications are subject to change without notice.

00_RX-V379_om_U.book Page 75 Tuesday, January 13, 2015 4:50 PM

Summary of Contents for RX-V379















































































Search results

Summary of Contents for RX-V379

Reviews:

Related manuals for RX-V379

Brands by name

Popular brands

Yamaha RX-V379, Owner'S Manual

Search results

Summary of Contents for RX-V379

Reviews:

Related manuals for RX-V379

Brands by name

Popular brands