Yamaha RX-V10MKII Owner'S Manual Download Page 41

Page: 41 / 42

English

SPECIFICATIONS

AUDIO SECTION

Minimum RMS Output Power per Channel
MAIN L, R

8 ohms, 20 Hz to 20 kHz, 0.04% THD

...................................................45W+45W

CENTER

8 ohms, 1 kHz, 0.04% THD ....................45W

REAR L,R

8 ohms, 1 kHz, 0.3% THD............15W+15W

Dynamic Power per Channel
(by IHF Dynamic Headroom measuring

method)
8 ohms..........................................65W+65W
6 ohms..........................................75W+75W
4 ohms..........................................95W+95W
2 ohms......................................105W+105W

DIN Standard Output Power per Channel

4 ohms, 1 kHz, 0.7% THD

[Europe model only]...................60W+60W

IEC Power per Channel

8 ohms, 1 kHz, 0.1% THD

[Europe model only]...................50W+50W

Power Band Width

8 ohms, 22.5W, 0.1% THD

..........................................10 Hz to 50 kHz

Maximum Power per Channel

[General model only]
MAIN L, R (1 kHz, 10% THD, 8 ohms)

.....................................................65W+65W

Input Sensitivity/Impedance

PHONO MM .....................2.5 mV/47 k-ohms
CD/TAPE

MD/DVD·LD/VCR/V-AUX

........................................150 mV/47 k-ohms

6CH DISCRT INPUT

MAIN L, R ......................150 mV/70 k-ohms
CENTER .......................150 mV/40 k-ohms
SURROUND L, R ...........90 mV/40 k-ohms
SUBWOOFER ..............150 mV/40 k-ohms

Maximum Input Signal (1 kHz, 0.5% THD)

PHONO MM......................................100 mV
CD/TAPE

MD/DVD·LD/VCR/V-AUX

(EFFECT ON) ........................................2.5V

Output Level/Impedance

REC OUT .......................150 mV/0.9 k-ohms
SUBWOOFER ...................3.5V/1.6 k-ohms

Headphone Jack Rated Output/Impedance

Output Level (8 ohms, 1 kHz, 150 mV Input)

.............................................................0.45V

Impedance.....................................330 ohms

Frequency Response (20 Hz to 20 kHz)

CD/TAPE

MD/DVD·LD/VCR/V-AUX

........................................................0±0.5 dB

RIAA Equalization Deviation

PHONO MM....................................0±0.5 dB

Total Harmonic Distortion

PHONO MM to REC OUT

20 Hz to 20 kHz, 1V..........................0.02%

CD/TAPE

MD/DVD·LD/VCR/V-AUX

to SP OUT

20 Hz to 20 kHz, 22.5W/8 ohms ......0.02%

Signal-to-Noise Ratio (IHF-A Network)

PHONO MM to REC OUT
(5 mV Input Shorted) ...........................82 dB
CD/TAPE

MD/DVD·LD/VCR/V-AUX to SP

OUT (Shorted) ....................................95 dB

Residual Noise (IHF-A Network)

MAIN L/R ...........................................140

Channel Separation (Vol. MAX, EFFECT OFF)

PHONO MM

(Input Shorted, 1 kHz) .......................60 dB

CD/TAPE

MD/DVD·LD/VCR/V-AUX

(Input 5.1 k-ohms Terminated, 1 kHz)

..........................................................60 dB

Tone Control Characteristics

BASS:

Boost/cut ................±10 dB (50 Hz)
Turnover Frequency .........(350 Hz)

TREBLE:

Boost/cut...........±10 dB (20 kHz)
Turnover Frequency.....(3.5 kHz)

Gain Tracking Error (0 to –60 dB) ............3 dB

VIDEO SECTION

Video Signal Level..................1 Vp-p/75 ohms

Maximum Input Level .........................1.5 Vp-p

Signal-to-Noise Ratio .............................50 dB

Monitor Out Frequency Response

..................................5 Hz to 10 MHz, –3 dB

FM SECTION

Tuning Range ......................87.5 to 108.0 MHz

50 dB Quieting Sensitivity

(IHF, 1 kHz, 100% mod., 75 ohms)

[General model only]

Mono ..............................1.6

V (15.3 dBf)

Stereo..............................23

V (38.5 dBf)

Usable Sensitivity (75 ohms)

DIN, Mono (S/N 26 dB)

[Europe and U.K. models] .................0.9

DIN, Stereo (S/N 46 dB)

[Europe and U.K. models] ..................28

Alternate Channel Selectivity

[General model].....................................75 dB

Selectivity (two signals, 40 kHz Dev., ±300 kHz)

[Europe and U.K. models] .....................55 dB

Signal-to-Noise Ratio

(IHF) Mono/Stereo

[General model] .......................80 dB/75 dB

(DIN-Weighted, 40 kHz Dev.) Mono/Stereo

[Europe and U.K. models] ........74 dB/69 dB

Harmonic Distortion

Mono/Stereo (1 kHz)

[General model] .............................0.1/0.2%

Mono/Stereo (40 kHz Dev.)

[Europe and U.K. models]..............0.1/0.2%

Stereo Separation (1 kHz)

[General model]....................................48 dB
[Europe and U.K. models (40 kHz Dev.)]

.............................................................48 dB

Frequency Response

30 Hz to 15 kHz ................................0 ±1 dB

AM SECTION

Tuning Range

[General model] ..................530 to 1,710 kHz
[Europe and U.K. models]
.............................................531 to 1,611 kHz

Usable Sensitivity .............................300

V/m

Signal-to-Noise Ratio .............................50 dB

AUDIO SECTION

Output Level

FM (100% mod., 1 kHz)

[General model] ...............................500 mV
[Europe and U.K. models (40 kHz Dev.)]

.........................................................400 mV

AM (30% mod., 1 kHz) .......................150 mV

GENERAL

Power Supply

[U.K. model] ..........................AC 230V, 50 Hz
[Europe model]......................AC 230V, 50 Hz
[General model]

....................AC 110/120/220/240V, 50/60 Hz

Power Consumption ...............................160W

Maximum Power Consumption

[General model only]............................360W

AC Outlets

2 SWITCHED OUTLETS

[Europe and General models]

..........................................100W max. total

1 SWITCHED OUTLET

[U.K. model] ......................100W max. total

Dimensions (W x H x D)

........................................280 x 119 x 389 mm

(11” x 4-11/16” x 15-5/16”)

Weight .............................7.3 kg (16 lbs. 1 oz.)

Accessories ..........................AM loop antenna

Indoor FM antenna

Remote controller

Batteries

75-ohm/300-ohm

antenna adapter

(U.K. model only)

Specifications are subject to change without
notice.

Summary of Contents for RX-V10MKII











































Search results

Summary of Contents for RX-V10MKII

Reviews:

Related manuals for RX-V10MKII

Brands by name

Popular brands

Yamaha RX-V10MKII, Owner'S Manual

Search results

Summary of Contents for RX-V10MKII

Reviews:

Related manuals for RX-V10MKII

Brands by name

Popular brands