En
44
CONNECTIONS
Setting up the speaker parameters automatically (YPAO)
■
Message list
■
When a warning message is displayed before measurement
■
Error messages
■
Warning messages
NOTE
If the following messages appear, resolve the problems that have occurred and carry out the
measurement process again.
Connect MIC!
The YPAO microphone is not connected.
Connect the YPAO microphone to the YPAO
MIC jack on the front panel.
Unplug HP!
The headphones are connected.
Remove the headphones.
Memory Guard!
The settings of this unit are protected.
Set “Memory Guard” in the Setup menu to “Off”
E-1:
No Front SP
The unit was not able to find the front
channel.
Check that the left and right front speakers are
connected correctly.
E-2:
No Sur. SP
The unit was only able to find one of side of
the surround channels.
Check that the left and right surround speakers
are connected correctly.
E-3:
No F.PRNS SP
The unit was only able to find one of side of
the presence channels.
Check that the left and right presence speakers are
connected correctly.
E-4:
SBR
→
SBL
Only one surround back speaker is
connected and only the right side surround
back channel sound is detected.
When only one surround back speaker is
connected, connect to the left side (SINGLE)
terminal.
E-5:
Noisy
The noise is too loud, preventing accurate
measurements from being taken.
Measure again in quiet surroundings. Turn off any
devices in the room that may be emitting noise, or
place them further away from the YPAO
microphone.
When this message is displayed, selecting
“PROCEED” will allow you to continue
measuring. However, we recommend resolving the
problem and measuring again, as continuing
measurement without doing so will not give
accurate results.
E-6:
Check Sur.
Even though surround left and right speakers
are not connected, only the surround back
speakers are connected.
When using surround back speakers, connection of
the surround left/right speakers is necessary.
E-7:
No MIC
The YPAO microphone has been removed.
While measuring, take care not to touch the
YPAO microphone.
E-8:
No Signal
The YPAO microphone could not
distinguish a test tone.
Check that the YPAO microphone has been
installed correctly.
Check that each speaker has been connected and
installed correctly.
The YPAO microphone or the YPAO MIC jack
may be broken. Inquire at the retailer where you
purchased this unit, or the nearest Yamaha service
center.
E-9:
User Cancel
You have carried out an operation that has
cancelled the measuring process.
Carry out the measuring process again. Do not
operate this unit by, for example, adjusting the
volume.
E-10:
Internal Error
An internal error has occurred.
Carry out the measuring process again. Contact a
Yamaha service center if “E-10” is displayed
again.
W-1:
Out of Phase
The speakers displayed are connected with
the opposite polarity. Depending on the type
of speakers you are using and the
environment in which you have them
installed, this message may occur even if the
speakers are connected correctly.
Depending on the type of speakers, “W-1” may
display even if the speakers are connected
correctly.
Check that the speaker po (positive), and -
(negative) are correct. If these are connected
correctly, you can use the speakers normally even
this message appears.
W-2:
Over 24m/80ft
The speakers displayed are separated from
the listening position by more than 24 m,
and cannot be adjusted correctly.
Install the speakers with 24 m of the listening
position.
W-3:
Level Error
Volume level varies greatly for individual
channels, and cannot be adjusted correctly.
Check that all speakers are installed in the same
surroundings.
Check that the speaker po (positive), and -
(negative) are correct.
We recommend the same speakers or speakers
with as similar specifications as possible.
Adjust the volume of the subwoofer.
If “W-2” or “W-3” appears, you can apply measurement results, but they will not give optimal
results. We recommend that you resolve the problem and carry out the measurement process again.
