![background image](http://html.mh-extra.com/html/yamaha/rs7000-ver-1-2/rs7000-ver-1-2_owners-manual_899785268.webp)
2. MIDI Events Handled by the RS7000
268
RS7000
●
Effect Send Level 1 (Reverb Effect)
(Control Number 091)
• Specifies the reverb effect send level.
●
Effect Send Level 3 (Chorus Effect)
(Control Number 093)
• Specifies the delay/chorus effect send level.
●
Effect Send Level 4 (Variation Effect)
(Control Number 094)
• Specifies the variation effect send level.
●
Data Increment (Control Number 096)
●
Data Decrement (Control Number 097)
• These MIDI messages increment or decrement by one the
value of pitch bend sensitivity, fine tune, or coarse tune settings
made using RPN (Page 269).
●
NRPN MSB (Non-Registered Parameter Number
MSB) (Control Number 099)
●
NRPN LSB (Non-Registered Parameter Number
LSB) (Control Number 098)
• Used primarily as offset values for vibrato, filter, EG, drum
setup and other settings.
• Data Entry (Page 267) is used to set the parameter value after
specifying the parameter using the NRPN MSB and LSB.
• Once an NRPN is specified, the following data entry message
received on the same channel is processed as the value of that
NRPN. Prevent operational errors by transmitting an RPN Null
message (7FH, 7FH) after using these messages to perform a
control operation.
• Refer to “8. NRPN” for information about the parameter. (Page
270)
●
RPN MSB (Registered Parameter Number MSB)
(Control Number 101)
●
RPN LSB (Registered Parameter Number LSB)
(Control Number 100)
• Used primarily as offset values for pitch bend sensitivity, tun-
ing, and other part settings.
• Data Entry (Page 267) is used to set the parameter value after
specifying the parameter using the RPN MSB and RPN LSB.
• Once an RPN is specified, the following data entry message
received on the same channel is processed as the value of that
RPN. Prevent operational errors by transmitting an Null mes-
sage (7FH, 7FH) after using these messages to perform a con-
trol operation.
• Refer to “7. RPN” for information about the parameter. (Page
269)
●
All Sound Off (Control Number 120)
• Turns all currently sounding notes off for all parts.
●
Reset All Controllers (Control Number 121)
• Resets all controllers to their initial values. The following
parameters are affected: Pitch Bend, Channel Pressure, Poly-
phonic Key Pressure, Modulation, Expression, Hold 1, Porta-
mento, Sostenuto, Soft Pedal, Portamento Control, RPN*,
NRPN* (* The RPN and NRPN are specified as having no
number, and no internal data is changed).
• The following data is not affected: Program Change, Bank
Select MSB and LSB, Volume, Pan, Dry Send Level, Effect
Send Level 1, 3, and 4, Pitch Sensitivity, Fine Tuning, Coarse
Tuning.
●
Omni Mode Off (Control Number 124)
• Performs the same operation as when an All Notes Off message
is received. The voice receive channel is set to 1.
●
Omni Mode On (Control Number 125)
• Performs the same operation as when an All Notes Off message
is received. Only the voice receive channel is set to Omni On.
●
Mono (Control Number 126)
• Performs the same operation as when an All Sound Off mes-
sage is received. If the 3rdbyte parameter (the parameter that
determines the mono number) is 0 ~ 16 the parts corresponding
to those channels are set to mono.
●
Poly (Control Number 127)
• Performs the same operation as when an All Sound Off mes-
sage is received, and sets the parts corresponding to those
channels are set to poly.
Summary of Contents for RS7000 Ver.1.2
