![background image](http://html.mh-extra.com/html/yamaha/rs7000-ver-1-2/rs7000-ver-1-2_owners-manual_899785247.webp)
4. The Sample Jobs
RS7000
247
5
The Sampling Mode
1
SAMPLE (Source Sample Number)
...........[Knob 1]
[Settings] 001 ~ 128, C001 ~ C128
Specifies the source sample voice.
2
KEY (Source Key Number)
............................[Knob 2]
[Settings] C-2 ~ G8
Specifies the key number of the source sample.
3
SAMPLE
(Destination Sample Number)
.....................[Knob 3]
[Settings] 001 ~ 128, C001 ~ C128
Specifies the destination sample voice.
4
TYPE (Destination Type)
................................[Knob 4]
[Settings] PITCHED, KIT: C-2 ~ G8
Specifies the type of the destination sample voice.
Selects the sample key number when the destination sample is a
Sample Kit Voice type.
5
AUDITION
.......................................................................[F2]
Plays the specified move source sample.
6
DO!
....................................................................................[F4]
Executes the job.
Maximizes (normalizes) the overall level of the specified sample.
1
SAMPLE (Sample Number)
...........................[Knob 1]
[Settings] 001 ~ 128, C001 ~ C128
Specifies the sample voice to be normalized.
2
KEY (Key Number)
........................................... [Knob 2]
[Settings] C-2 ~ G8
Specifies the key number of the sample to be normalized.
3
RATIO
..................................................................... [Knob 3]
[Settings] 001 ~ 800%
Specifies the post-normalization sample level.
A setting of 100% maximizes the level so that the highest
peak level in the sample is just below clipping (maximum
digital signal level).
Settings below 100% reduce the level of the sample accord-
ingly.
Settings higher than 100% will raise the sample level above
the maximum, producing deliberate clipping.
4
AUDITION
...................................................................... [F2]
Plays the specified sample.
Plays the normalized sample if pressed after [F4] (DO!) is
pressed to normalize the sample.
5
DO!
................................................................................... [F4]
Executes the job.
6
CREATE
......................................................................... [F3]
Saves the processed sample to the target sample number,
overwriting the original sample.
If the original sample is a Pitched Sample it will be overwrit-
ten at this point. If the original sample is part of a Sample Kit
Voice a key-number selection page will appear.
7
CREATE TO
(Destination Key Number)
............................ [Knob 2]
[Settings] C-2 ~ G8
Specifies the key number to which the processed sample will
be saved.
NOTE
• This parameter is not available when the
specified source sample is a Pitched Voice.
• When the last remaining sample is moved
from a Sample Kit Voice, the entire sample
voice is deleted.
NOTE
The PITCHED option is not available when a
Sample Kit Voice is stored in the destination
sample voice number.
05 NORMALIZE
3
5
6
1
2
4
[Knob 1]
[Knob 2]
[Knob 3]
[F4]
[F2]
[F3]
NOTE
This parameter is not available when the speci-
fied sample is a Pitched Voice.
Original
Waveform
100%
Lower than 100% Higher than 100%
8
7
[Knob 2]
[F3]
Summary of Contents for RS7000 Ver.1.2
