manualshive.com logo in svg

Yamaha Royal Star XVZ13CTMW, Owner'S Manual

Share
Download
Yamaha Royal Star XVZ13CTMW Owner'S Manual Download Page 92

CONSUMER INFORMATION

9-1

9

EAU26351

Identification numbers 

Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.
KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION 
NUMBER:

MODEL LABEL INFORMATION:

EAU26381

Key identification number 

The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.

EAU26400

Vehicle identification number 

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.

NOTE:

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor-
cycle with the licensing authority in your
area.

1. Key identification number

1. Vehicle identification number

U1D612E0.book  Page 1  Tuesday, May 16, 2006  9:28 AM

Summary of Contents for Royal Star XVZ13CTMW







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands