Yamaha Raptor YFM35RA Page 99 Owner'S Manual Download | Manualshive

Page: 99 / 142

background image

8-27

8

TIP

If the cable length cannot be adjusted to specifica-
tion, consult a Yamaha dealer.

6. Tighten the locknut on the brake cable.
7. Slide the rubber cover to its original position.
8. Turn in the adjusting bolt at the rear brake cal-

iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.

NOTICE:

When tightening the locknut,

hold the adjusting bolt with a wrench so
that it does not turn together with the lock-
nut.

[ECB00521]

WARNING

EWB02090

Operating with improperly serviced or adjust-
ed brakes could cause the brakes to malfunc-
tion, resulting in reduced braking
performance. This could increase the chance
of a collision or accident. After adjusting the
parking brake free play, block the rear of the
ATV off the ground and spin the rear wheels.
Check to make sure there is no brake drag. If
brake drag is noticed, perform the adjustment
again.

EBU24742

Brake light switches

The brake light, which is activated by the brake
pedal and brake lever, should come on just before
braking takes effect.

1. Locknut

2. Adjusting nut

3. Rubber cover

1

2

(a)

(b)

3

Tightening torque:

Locknut (rear brake caliper):

16 Nm (1.6 m·kgf, 12 ft·lbf)

U1BS11E0.book Page 27 Monday, April 5, 2010 8:56 AM

«
...
97
98
99
100
101
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: Kellfri Pages: 16

Brand: Suzuki Pages: 576

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 155

Brand: Yamaha Pages: 190

Brand: Pongratz Pages: 8

Brand: Logan Pages: 28

2009 Ranger RZR 800 EFI

Brand: Polaris Pages: 332

Brand: Razor Pages: 12

Brand: Yamaha Pages: 178

Brand: Cushman Pages: 176

Brand: Ifor Williams Trailers Pages: 55

2001 TRX250EX Sportrax 250EX

Brand: Honda Pages: 153

Brand: Hisun Motors Pages: 67

Brand: Hisun Motors Pages: 65

Brand: Hisun Pages: 68

Brand: Hisun Pages: 75

Brand: Hisun Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands