Yamaha Raptor YFM35RA Owner'S Manual Download | Manualshive

Page: 97 / 142

background image

8-25

8

EBU24291

Changing the brake fluid

Have a Yamaha dealer change the brake fluid at
the intervals specified in the TIP after the periodic
maintenance and lubrication chart. In addition,
have the oil seals of the master cylinders and cali-
pers as well as the brake hoses replaced at the in-
tervals listed below or whenever they are damaged
or leaking.

●

Oil seals: Replace every two years.

●

Brake hoses: Replace every four years.

EBU24394

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

EBU24592

Checking the brake pedal position

The brake pedal position must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.
The top of the brake pedal should be positioned
50.2 mm (1.98 in) above the top of the frame as
shown. If the brake pedal is not positioned as spec-
ified, have a Yamaha dealer adjust it.

1. No brake lever free play

U1BS11E0.book Page 25 Monday, April 5, 2010 8:56 AM

«
...
95
96
97
98
99
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: ShoreLand'r Pages: 11

Brand: Taylor-Dunn Pages: 144

Brand: Yamaha Pages: 54

Brand: Toro Pages: 28

Brand: Yamaha Pages: 13

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 13

Brand: Yamaha Pages: 47

Brand: Yamaha Pages: 16

GRIZZLY 125 YFM125GY

Brand: Yamaha Pages: 130

GRIZZLY 125 YFM125GZ

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 64

GRIZZLY 125 YFM125GD

Brand: Yamaha Pages: 134

GRIZZLY 125 YFM125GA

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 124

FX Nytro FX10MTRAX

Brand: Yamaha Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands