Yamaha Raptor YFM35RA Page 95 Owner'S Manual Download | Manualshive

Page: 95 / 142

background image

8-23

8

TIP

The wheels need to be removed to check the
brake pads. (See page 8-44.)

EBU28800

Rear brake pads

Each brake pad is provided with two wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-
tor grooves. If a brake pad has worn to the point
that a wear indicator groove almost appears, have
a Yamaha dealer replace the brake pads as a set.

EBU29840

Checking the brake fluid level

Insufficient brake fluid may allow air to enter the
brake system, possibly causing it to become inef-
fective.
Before riding, check that the brake fluid is above
the minimum level mark and replenish if neces-
sary. A low brake fluid level may indicate worn
brake pads and/or brake system leakage. If the
brake fluid level is low, be sure to check the brake
pads for wear and the brake system for leakage.

1. Wear indicator groove

1. Wear indicator groove

U1BS11E0.book Page 23 Monday, April 5, 2010 8:56 AM

«
...
93
94
95
96
97
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: Hisun Pages: 93

Brand: Roketa Pages: 15

Formula Mx 1988

Brand: BOMBARDIER Pages: 62

traxter max series

Brand: BOMBARDIER Pages: 174

outlander max 800

Brand: BOMBARDIER Pages: 160

Brand: BOMBARDIER Pages: 282

Brand: Can-Am Pages: 147

ESCALATE TRAILER ET 5000W

Brand: Bil-Jax Pages: 20

Brand: Baja motorsports Pages: 77

Brand: CHICAGO Pages: 25

Brand: Yamaha Pages: 119

Brand: Bennche Pages: 181

Brand: Salsco Pages: 42

Brand: Arctic Cat Pages: 92

Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL

Brand: Kendon Pages: 20

Brand: Yamaha Pages: 126

Brand: Bailey Pages: 102

Brand: Jula Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands