Yamaha Raptor YFM35RA Owner'S Manual Download | Manualshive

Page: 94 / 142

background image

8-22

8

4. Tighten the locknut.
5. Slide the rubber cover to its original position.

EBU24060

Valve clearance

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29601

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be per-
formed by a Yamaha dealer.

WARNING

EWB02571

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

EBU24130

Checking the front and rear brake pads

The front and rear brake pads must be checked for
wear at the intervals specified in the periodic main-
tenance and lubrication chart.

EBU28790

Front brake pads

Each brake pad is provided with two wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-
tor grooves. If a brake pad has worn to the point
that a wear indicator groove almost appears, have
a Yamaha dealer replace the brake pads as a set.

1. Rubber cover

2. Throttle cable free play adjusting bolt
3. Locknut

4. Throttle cable free play

3

1

2

4

U1BS11E0.book Page 22 Monday, April 5, 2010 8:56 AM

«
...
92
93
94
95
96
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: Yamaha Pages: 176

Brand: BOMBARDIER Pages: 99

LEXION 770 2016

Brand: Claas Pages: 48

Brand: Seizmik Pages: 10

Brand: FLEMING Pages: 6

GMX 125 SPORTZILLA X

Brand: GMX MOTORBIKES Pages: 28

Brand: Can-Am Pages: 140

2009 Renegade 500

Brand: Can-Am Pages: 148

Brand: gio Pages: 20

Brand: Mi-T-M Pages: 65

Brand: PRONAR Pages: 135

Brand: Polaris Pages: 109

Brand: LJ'S TOPS & BOTTOMS Pages: 14

Brand: SSR Motorsports Pages: 55

Brand: HAKO Pages: 190

Brand: Hammerhead Pages: 55

Brand: BOMBARDIER Pages: 44

Brand: Yamaha Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands