Yamaha Raptor YFM35RA Owner'S Manual Download | Manualshive

Page: 40 / 142

background image

6-1

6

EBU19873

OPERATION

WARNING

EWB00011

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU19901

Read the Owner’s Manual carefully before riding
the ATV. If there is a control or function you do not
understand, ask your Yamaha dealer.

WARNING

EWB00631

Read the Owner’s Manual carefully to become
familiar with all controls in order to help pre-
vent any loss of control, which could cause an
accident or injury.

EBU20163

Starting a cold engine

NOTICE

ECB00150

See the “Engine break-in” section on page 6-6
prior to operating the engine for the first time.

1. Set the parking brake.
2. Turn the fuel cock to “ON”.
3. Turn the key to “ON” and the engine stop

switch to “

”.

4. Shift the transmission into neutral. The neutral

indicator light should come on. If the indicator
light does not come on, have a Yamaha deal-
er check the electrical circuit.

TIP

This model is equipped with an ignition circuit cut-
off system. The engine can be started under the
following conditions.

●

The transmission is in neutral.

●

The clutch is disengaged with the shift pedal and
the drive select lever in any position. However, it
is recommended to shift into neutral before start-
ing the engine.

5. Use the starter (choke) in reference to the fig-

ure:

Position (1):

Cold engine start with ambient temperature
below 5 °C (40 °F).

U1BS11E0.book Page 1 Monday, April 5, 2010 8:56 AM

«
...
38
39
40
41
42
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: J&M Pages: 25

Brand: Baja motorsports Pages: 44

Brand: XY Powersports Pages: 259

Brand: Polaris Pages: 690

Brand: LAMAX Pages: 150

Brand: Massimo Pages: 8

Brand: Kellfri Pages: 16

Brand: Kazuma Pages: 25

Brand: Har-Tru Pages: 12

RANGER XP 1000 2018

Brand: Polaris Pages: 565

Brand: Qpod Pages: 12

Brand: Kellfri Pages: 20

Brand: Kipor Pages: 102

2005 LT-A700XK5

Brand: Suzuki Pages: 477

Big Bear YFM350UBL

Brand: Yamaha Pages: 170

Challenger4 300

Brand: TrailMaster Pages: 15

Brand: TrailMax Pages: 58

Brand: TrailMax Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands