Yamaha Raptor YFM35RA Page 37 Owner'S Manual Download | Manualshive

Page: 37 / 142

background image

5-4

5

EBU19770

Drive chain

Check the condition of the drive chain and check
the drive chain slack. Lubricate and adjust the
drive chain as necessary. (See page 8-29.)

EBU19794

Tires

Check tire pressure regularly to make sure it is at
the recommended specifications. Also check for
wear and damage.

Tire pressure

Use the low-pressure tire gauge to check and ad-
just tire pressures when the tires are cold. Tire
pressures must be equal on both sides.

WARNING! Operation of this vehicle with im-
proper tire pressure may cause severe injury
or death from loss of control or rollover. Tire
pressure below the minimum specified could
also cause the tire to dislodge from the rim un-
der severe riding conditions.

[EWB02541]

Set tire

pressures to the following specifications:

The low-pressure tire gauge is included as stan-
dard equipment. Make two measurements of the
tire pressure and use the second reading. Dust or
dirt in the gauge could cause the first reading to be
incorrect.

Recommended tire pressure:

Front

25.0 kPa (0.250 kgf/cm², 3.6 psi)

Rear

25.0 kPa (0.250 kgf/cm², 3.6 psi)

Minimum tire pressure:

Front

22.0 kPa (0.220 kgf/cm², 3.2 psi)

Rear

22.0 kPa (0.220 kgf/cm², 3.2 psi)

Maximum tire seating pressure:

Front

250 kPa (2.5 kgf/cm², 36 psi)

Rear

250 kPa (2.5 kgf/cm², 36 psi)

U1BS11E0.book Page 4 Monday, April 5, 2010 8:56 AM

«
...
35
36
37
38
39
...
»

Summary of Contents for Raptor YFM35RA















































































































































Reviews:

No comments

Related manuals for Raptor YFM35RA

Brand: Massimo Pages: 115

Brand: Baja motorsports Pages: 69

Brand: TGB Pages: 109

Brand: Egholm Pages: 16

Brand: PRONAR Pages: 147

Brand: KTM Pages: 197

Brand: PRONAR Pages: 125

Brand: Yamaha Pages: 38

Brand: Yamaha Pages: 504

Brand: Wood-mizer Pages: 90

Brand: HEIL Pages: 202

Brand: Herculano Pages: 36

Brand: Hisun Pages: 63

Brand: Hisun Pages: 68

2009 Sportsman X2 500 EFI

Brand: Polaris Pages: 148

CARRYALL 252 2007

Brand: Club Car Pages: 52

Brand: Arctic Cat Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands