Yamaha Raptor YFM35RA Owner'S Manual Download Page 114

Page: 114 / 142

8-42

5. Install the headlight bulb holder by aligning the

projections with the holes in the headlight unit,
pushing it inward, and turning it clockwise until
it stops.

6. Install the headlight bulb holder cover at the

rear of the headlight.

NOTICE:

Make sure the

headlight bulb holder cover is securely fit-
ted over the bulb holder and seated prop-
erly.

[ECB00671]

7. Adjust the headlight beam if necessary.

EBU25561

Adjusting a headlight beam

NOTICE

ECB00690

It is advisable to have a Yamaha dealer make
this adjustment.

To raise a headlight beam, turn the headlight beam
adjusting bolt in direction (a).

1. Do not touch the glass part of the bulb.

U1BS11E0.book Page 42 Monday, April 5, 2010 8:56 AM

Summary of Contents for Raptor YFM35RA















































































































































Search results

Summary of Contents for Raptor YFM35RA

Reviews:

Brands by name

Popular brands

Yamaha Raptor YFM35RA, Owner'S Manual

Search results

Summary of Contents for Raptor YFM35RA

Reviews:

Brands by name

Popular brands