manualshive.com logo in svg

Yamaha PLG150-DX, Owner'S Manual

Share
Download
Yamaha PLG150-DX Owner'S Manual Download Page 68

68

Setup Menus / 

DX Simulator Setup

Insert  & Transmit Tab

This tab features various settings related to how the DX data is inserted to the host

application sequence data (using the 

Insert DX Bulk Dump Data

 function) or trans-

mitted to the PLG150-DX (using the 

Transmit DX Bulk Dump Data

 function).

• Method

1 Voice

When this is selected, only the edited data for one voice will be inserted or transmitted.

• Be careful when using “1 Voice.”  If you’ve inserted “1 Voice” (only the edited data) and then

change the voice on the PLG150-DX, you may not be able to revert back to the edited voice.
Use 

Transmit DX Bulk Dump Data

 to transmit the desired data to the PLG150-DX.

All Voices

When this is selected, the data for all 64 Custom voices will be inserted or transmitted.

Bulk Dump Interval

This determines the amount of time (in seconds) that separates each “packet” of data
inserted or transmitted.  If the tone generator or sound card “chokes” on the incoming
MIDI data, or the insert/transmit operation doesn’t seem to work as expected, try set-
ting the Interval to a higher number.

• Insert Method

 (Plug-in Editor only)

Create a New Block

When this is selected, a new block (containing the inserted DX bulk dump data) is cre-
ated to a track in host application.

Insert into a Block

When this is selected, the inserted DX bulk dump data is put into an existing block in
host application.

Interval

This determines the amount of time (in clocks) that separates each insertion.  If the
tone generator or sound card “chokes” on the incoming MIDI data, or host application
has trouble sending all the data properly, or the DX voices don't seem to work as
expected, try setting the Interval to a higher number.

Summary of Contents for PLG150-DX













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands