MX49/MX61 Data List
53
MIDI Data Format
Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal
or binary numbers. Hexadecimal numbers may include the letter “H” as a suffix. The letter
“n” indicates a certain whole number.
The chart below lists the corresponding decimal number for each hexadecimal number.
Additional Notes
• For example, 144 – 159(Decimal)/9nH/1001 0000 – 1001 1111(Binary) indicate the note-
on messages for the channels 1 through 16 respectively. 176 – 191/BnH/1011 0000 –
1011 1111 indicate the control change messages for the channels 1 through 16
respectively. 192 – 207/CnH/1100 0000 – 1100 1111 indicate the program change
messages for the channels 1 through 16 respectively. 240/F0H/1111 0000 is positioned
at the beginning of data to indicate a system exclusive message. 247/F7H/1111 0111 is
positioned at the end of the system exclusive message.
• aaH (Hexadecimal)/0aaaaaaa (Binary) indicates the data addresses. The data address
consists of High, Mid and Low.
• bbH/0bbbbbbb indicates byte counts.
• ccH/0ccccccc indicates check sums.
• ddH/0ddddddd indicates data/value.
SYNTHESIZER/SEQUENCER PART
(1) TRANSMIT FLOW
MIDI <-+-[SW1]--+---------NOTE ON/OFF
9nH
OUT |
|
|
+---------KEY'S AFTER TOUCH
AnH (Seq only)
|
|
|
+---------CONTROL CHANGE (All in Seq)
|
|
MODULATION
BnH, 01H
|
|
VOLUME
BnH, 07H
|
|
PAN
BnH, 0AH
|
|
EG SUSTAIN LEVEL
BnH, 1FH
|
|
SUSTAIN SWITCH
BnH, 40H
|
|
FILTER RESONANCE
BnH, 47H
| |
EG RELEASE TIME
BnH, 48H
| |
EG ATTACK TIME
BnH, 49H
| |
FILTER CUTOFF FREQ
BnH, 4AH
| |
EG DECAY TIME
BnH, 4BH
| |
REVERB SEND
BnH, 5BH
| |
CHORUS SEND
BnH, 5DH
| |
ASSIGNABLE CONTROLLERS
BnH, (00H .. 5FH)
| |
|
+--[SW7]--BANK SEL MSB
BnH, 00H
|
|
BANK SEL LSB
BnH, 20H
|
|
|
+---------CHANNEL MODE MESSAGE (Seq only)
|
|
RESET ALL CONTROLLERS
BnH, 79H
|
|
LOCAL CONTROL
BnH, 7AH
|
|
OMNI MODE OFF
BnH, 7CH
|
|
OMNI MODE ON
BnH, 7DH
|
|
MONO MODE ON
BnH, 7EH
|
|
POLY MODE ON
BnH, 7FH
|
|
|
+--[SW8]--PROGRAM CHANGE
CnH
|
|
|
+---------CHANNEL AFTER TOUCH
DnH (Seq only)
|
|
|
+---------PITCH BEND CHANGE
EnH
|
+--[SW3]-----------SYSTEM REALTIME MESSAGE
|
TIMING CLOCK
F8H
|
+--[SW4]-----------SYSTEM REALTIME MESSAGE
|
START
FAH
|
CONTINUE
FBH
|
STOP
FCH
|
+------------------ACTIVE SENSING
FEH
|
+--[SW5]-+---------SYSTEM EXCLUSIVE MESSAGE (All in Seq)
|
+---------<BULK DUMP>
|
|
F0H 43H 0nH 7FH 17H bhH blH ahH amH alH ddH....ddH ccH F7H
|
|
|
+---------<PARAMETER CHANGE>
|
F0H 43H 1nH 7FH 17H ahH amH alH ddH.....ddH F7H
|
+------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REPLY
F0H 7EH 7FH 06H 02H 43H 00H 41H 47H 06H 00H 00H 00H 7FH F7H
[SW1]
MIDI Transmit Channel
The data is transmitted over the specified channel for the current Part.
However, Program Change messages for changing the Performance are transmitted over the Basic Channel.
[SW3]
MIDI Clock Out
[SW4]
Seq MIDI Control
[SW5]
MIDI Device Number
When set to all, transmitted via 1.
[SW7]
SYSTEM Bank Select Switch
[SW8]
SYSTEM Program Change Switch
Decimal
Hexadecimal
Decimal
Hexadecimal
0
0
64
40
1
1
65
41
2
2
66
42
3
3
67
43
4
4
68
44
5
5
69
45
6
6
70
46
7
7
71
47
8
8
72
48
9
9
73
49
10
0A
74
4A
11
0B
75
4B
12
0C
76
4C
13
0D
77
4D
14
0E
78
4E
15
0F
79
4F
16
10
80
50
17
11
81
51
18
12
82
52
19
13
83
53
20
14
84
54
21
15
85
55
22
16
86
56
23
17
87
57
24
18
88
58
25
19
89
59
26
1A
90
5A
27
1B
91
5B
28
1C
92
5C
29
1D
93
5D
30
1E
94
5E
31
1F
95
5F
32
20
96
60
33
21
97
61
34
22
98
62
35
23
99
63
36
24
100
64
37
25
101
65
38
26
102
66
39
27
103
67
40
28
104
68
41
29
105
69
42
2A
106
6A
43
2B
107
6B
44
2C
108
6C
45
2D
109
6D
46
2E
110
6E
47
2F
111
6F
48
30
112
70
49
31
113
71
50
32
114
72
51
33
115
73
52
34
116
74
53
35
117
75
54
36
118
76
55
37
119
77
56
38
120
78
57
39
121
79
58
3A
122
7A
59
3B
123
7B
60
3C
124
7C
61
3D
125
7D
62
3E
126
7E
63
3F
127
7F
