manualshive.com logo in svg

Yamaha MusicCast AVENTAGE RX-A4A, User Manual

The Yamaha MusicCast AVENTAGE RX-A4A is a high-performance AV receiver that delivers exceptional audio quality and functionality. To unlock its full potential, you can easily obtain the user manual for free download on our website manualshive.com. Discover the ultimate audio experience with this state-of-the-art device.

Share
Download
background image

Updating the unit’s firmware via the network

When the unit is connected to the Internet and a firmware update is ready, the following message appears
after SETUP is pressed.

Confirm the message and start the firmware update via the network.

NOTICE

(

Do not operate the unit or disconnect the power cable or network cable during firmware update. If the firmware update is
interrupted, there is a possibility that the unit will malfunction. In this case, contact your nearest authorized Yamaha dealer or
service center to request repair.

1

Read the on-screen description.

2

Select “START”.

The on-screen display turns off and the firmware update begins.

3

When “UPDATE SUCCESS PLEASE POWER OFF!” appears on the front display, press

z

 on the front panel.

The firmware update is complete.

NOTE

(

Firmware update takes about 20 minutes or more.

(

If the Internet connection speed is slow, or the unit is connected to the wireless network, you might not get the message of new
firmware depending on the condition of the network connection. In this case, update the firmware using the USB flash drive.

n

Firmware update reservation

In step 2, select “LATER” for reservation to perform the firmware update when turning off the unit.

With an update reservation, the firmware update confirmation screen is displayed when you turn off the unit.

Press ENTER on the front panel or on the remote control to start the firmware update. After the firmware
update is complete, the unit will turn off automatically.

321

UPDATE > Updating the unit’s firmware

Summary of Contents for MusicCast AVENTAGE RX-A4A




























































































































































































































































































































































































































Reviews:

No comments

Related manuals for MusicCast AVENTAGE RX-A4A

Parallel Audio M4000 Operation Manual preview
M4000
Brand: Parallel Audio Pages: 8
Panasonic TU-DST52 Operating Instructions Manual preview
TU-DST52
Brand: Panasonic Pages: 44
Panasonic TU-DST52F User Manual preview
TU-DST52F
Brand: Panasonic Pages: 44
Panasonic SAHE200 - RECEIVER Manual preview
SAHE200 - RECEIVER
Brand: Panasonic Pages: 25
Panasonic PressIT TY-SB01WP Operating Instructions Manual preview
PressIT TY-SB01WP
Brand: Panasonic Pages: 25
VIETA HRE75B Owner'S Manual preview
HRE75B
Brand: VIETA Pages: 66
Harman BDS 280 Quick Start Manual preview
BDS 280
Brand: Harman Pages: 30
Yamaha HTR-4063 Quick Reference Manual preview
HTR-4063
Brand: Yamaha Pages: 8
Yamaha HTR-3064 Series Quick Reference Manual preview
HTR-3064 Series
Brand: Yamaha Pages: 8
Yamaha Aventage RX-A820 New Product Bulletin preview
Aventage RX-A820
Brand: Yamaha Pages: 2
Yamaha Aventage RX-A770 Firmware Update Procedure preview
Aventage RX-A770
Brand: Yamaha Pages: 6
Yamaha Aventage RX-A720 Setup Manual preview
Aventage RX-A720
Brand: Yamaha Pages: 18
Yamaha AVENTAGE RX-A1060 Firmware Update Manual preview
AVENTAGE RX-A1060
Brand: Yamaha Pages: 6
Yamaha Aventage RX-A1020 Easy Setup Manual preview
Aventage RX-A1020
Brand: Yamaha Pages: 8
F&U MPF3473HU User Manual preview
MPF3473HU
Brand: F&U Pages: 14
Icom ID-52A Manual preview
ID-52A
Brand: Icom Pages: 8
Kaon KTF-I2001CO User Manual preview
KTF-I2001CO
Brand: Kaon Pages: 25
Yaesu FT-891 Firmware Update Manual preview
FT-891
Brand: Yaesu Pages: 13

Brands by name

Popular brands

Load more brands