Yamaha MTN850-A 2017 Service Manual Download Page 551

Page: 551 / 560

EVENT CODE TABLE

9-18

EAS20164

EVENT CODE TABLE

No.

Item

Symptom

Possible causes

Note

192

Intake air pres-

sure sensor 1

Brief abnormality

detected in the intake

air pressure sensor 1

Same as for fault code

number P0107 and

P0108

Perform the checks and

maintenance jobs for fault

code number P0107 and

P0108.

193

Throttle position

sensor

Brief abnormality

detected in the throt-

tle position sensor

Same as for fault code

number P0122, P0123,

P0222, P0223 and

P2135

Perform the checks and

maintenance jobs for fault

code number P0122,

P0123, P0222, P0223 and

P2135.

195

Sidestand switch

Brief abnormality

detected in the ECU

(black/red lead) input

line

Same as for fault code

number P1601

Perform the checks and

maintenance jobs for fault

code number P1601.

196

Coolant tempera-

ture sensor

Brief abnormality

detected a in the

coolant temperature

sensor

Same as for fault code

number P0117 and

P0118

Perform the checks and

maintenance jobs for fault

code number P0117 and

P0118.

197

Intake air temper-

ature sensor

Brief abnormality

detected in the intake

air temperature sen-

sor

Same as for fault code

number P0112 and

P0113

Perform the checks and

maintenance jobs for fault

code number P0112 and

P0113.

199

Intake air pres-

sure sensor 2

Brief abnormality

detected in the intake

air pressure sensor 2

Same as for fault code

number P1606 and

P1607

Perform the checks and

maintenance jobs for fault

code number P1606 and

P1607.

203

Lean angle sen-

sor

Brief abnormality

detected in the lean

angle sensor

Same as for fault code

number P1604 and

P1605

Perform the checks and

maintenance jobs for fault

code number P1604 and

P1605.

207

Accelerator posi-

tion sensor

Brief abnormality

detected in the accel-

erator position sensor

Same as for fault code

number P2122, P2123,

P2127, P2128 and

P2138

Perform the checks and

maintenance jobs for fault

code number P2122,

P2123, P2127, P2128 and

P2138.

240

sensor

(Stuck at the

upper limit for

adjustment)

During O

feedback,

the adjustment is

maintained at the

upper limit

•

Open or short circuit in

the wire harness

between the sensor

and ECU

•

Drop in fuel pressure

•

Clogged fuel injector

•

Fault in sensor

•

Malfunction in ECU

•

Malfunction in the fuel

injection system

•

If a fault code is occurring,

respond to that first.

* Rarely, code 240 occurs

even when the system is

functioning properly.

241

sensor

(Stuck at the

lower limit for

adjustment)

During O

feedback,

the adjustment is

maintained at the

lower limit

•

Open or short circuit in

the wire harness

between the sensor

and ECU

•

Drop in fuel pressure

•

Clogged fuel injector

•

Fault in sensor

•

Malfunction in ECU

•

Malfunction in the fuel

injection system

•

If a fault code is occurring,

respond to that first.

* Rarely, code 241 occurs

even when the system is

functioning properly.

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 551 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: