Yamaha MTN850-A 2017 Service Manual Download Page 546

Page: 546 / 560

SELF-DIAGNOSTIC FUNCTION AND DIAGNOSTIC CODE TABLE

9-13

EAS31795

SELF-DIAGNOSTIC FUNCTION TABLE (FOR IMMOBILIZER SYSTEM)

TIP

For details of the fault code, refer to “SELF-DIAGNOSIS FAULT CODE INDICATION” on page 8-115.

EAS31119

COMMUNICATION ERROR WITH THE METER

EAS31120

DIAGNOSTIC CODE: SENSOR OPERATION TABLE

Fault

code No.

Item

Immobilizer unit: Code cannot be transmitted between the key and the immobilizer unit.

Immobilizer unit: Codes between the key and immobilizer unit do not match.

Immobilizer unit: Codes cannot be transmitted between the ECU and the immobilizer unit.

Immobilizer unit: Codes transmitted between the ECU and the immobilizer unit do not match.

Immobilizer unit: Key code registration malfunction.

ECU: Unidentified code is received.

Fault

code No.

Item

Probable cause of

malfunction

Vehicle symptom

Fail-safe system

operation

U0155

(Yamaha

diagnostic

tool)

Err (multi-

function

meter dis-

play)

CAN communication

error (with the meter)

Communication

between the ECU and

the meter is not possi-

ble

•

Defective meter cou-

pler and ECU cou-

pler

•

Open or short cir-

cuit in the wire har-

ness between the

meter and the ECU

•

Defective meter

•

Defective ECU

Defective meter dis-

play.

Traction control does

not work.

Grip warmer output:

OFF is fixed.

MAP changeover:

State is fixed.

Traction control does

not work.

Meter switch input:

OFF is fixed.

Diagnostic

code No.

Item

Tool display

Procedure

Throttle position sensor sig-

nal 1

•

Fully closed position

11–21

Check with throttle valves

fully closed.

•

Fully open position

96–106

Check with throttle valves

fully open.

Intake air pressure 1

Displays the intake air pres-

sure.

Operate the throttle while

pushing the “ ” side of the

start/engine stop switch. (If

the display value changes,

the performance is OK.)

Intake air pressure 2

Displays the intake air pres-

sure.

Operate the throttle while

pushing the “ ” side of the

start/engine stop switch. (If

the display value changes,

the performance is OK.)

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 546 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: