manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 336 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 336

FUEL TANK

7-3

EAS30450

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank cap with a pump.

2. Remove:

•

Rider seat

•

Air scoop/Fuel tank cover
Refer to “GENERAL CHASSIS (1)” on page
4-1.

3. Disconnect:

•

Fuel hose (fuel tank side)

•

Fuel pump coupler

•

Fuel tank drain hose

•

Fuel tank breather hose

WARNING

EWA17320

Cover fuel hose connections with a cloth

when disconnecting them. Residual pres-

sure in the fuel lines could cause fuel to

spurt out when removing the hose.

NOTICE

ECA17490

Be sure to disconnect the fuel hose by hand.

Do not forcefully disconnect the hose with

tools.

TIP

•

While pushing the ends “a” of the fuel hose
connector cover “1” in direction “b”, slide the
fuel hose connector cover in direction “c”, and
then remove the hose from the fuel pump.

•

Before removing the hose, place a few rags in
the area under where it will be removed.

•

It is prohibited to wear the cotton work gloves
or equivalent coverings.

4. Remove:

•

Fuel tank

TIP

Do not set the fuel tank down so that the instal-
lation surface of the fuel pump is directly under
the tank. Be sure to lean the fuel tank in an up-
right position.

EAS30451

REMOVING THE FUEL PUMP

1. Remove:

•

Fuel pump

NOTICE

ECA14721

• Do not drop the fuel pump or give it a

strong shock.

• Do not touch the base section of the fuel

sender.

EAS30454

CHECKING THE FUEL PUMP BODY

1. Check:

•

Fuel pump body
Obstruction 

 Clean.

Cracks/damage 

 Replace fuel pump as-

sembly.

EAS30455

CHECKING THE FUEL PUMP OPERATION

1. Check:

•

Fuel pump operation
Refer to “CHECKING THE FUEL PRES-
SURE” on page 7-11.

a

1

b

b

c

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments