manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 211 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 211

FRONT FORK

4-66

3. Check:

•

Damper rod “1”
Damage/wear 

 Replace.

Obstruction 

 Blow out all of the oil passag-

es with compressed air.

NOTICE

ECA19110

• The front fork leg has a very sophisticated

internal construction, which are particular-

ly sensitive to foreign material.

• When disassembling and assembling the

front fork leg, do not allow any foreign ma-

terial to enter the front fork.

EAS30209

ASSEMBLING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.

WARNING

EWA17090

• Note that the amount of the fork oil is differ-

ent in the left and right front fork legs. Make

sure to fill each of the left and right front

fork legs with the specified amount of the

fork oil.

• If both front fork legs are not filled with the

specified amount of the fork oil, it may

cause poor handling and a loss of stability.

TIP

•

When assembling the front fork leg, be sure to
replace the following parts:
–Inner tube bushing
–Outer tube bushing
–Oil seal
–Oil seal clip
–Dust seal
–Copper washer
–O-ring

•

Before assembling the front fork leg, make
sure all of the components are clean.

1. Install:

•

Damper rod assembly “1”

NOTICE

ECA19120

Allow the damper rod assembly to slide

slowly down the inner tube “2” until it pro-

trudes from the bottom of the inner tube. Be

careful not to damage the inner tube.

2. Tighten:

•

Damper rod assembly bolt
(along with the copper washer 

)

TIP

While holding the damper rod assembly with the
damper rod holder “1”, tighten the damper rod
assembly bolt.

3. Lubricate:

•

Inner tube’s outer surface

4. Install:

•

Dust seal “1” 

Front fork damper rod assembly 

bolt

23 N·m (2.3 kgf·m, 17 lb·ft)

LOCTITE®

Damper rod holder (ø27)

90890-01582

Damper rod holder

YM-01582

Recommended oil

Yamaha Suspension Oil 01

New

T

R

.

.

1

New

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments