Utility
MOTIF-RACK XS Owner’s Manual
102
Basic Structure
Ref
erence
V
oice
Multi
Utility
The Contr
ols &
Connector
s
Setting Up
Listening to
the Sound
Connections
Using a Computer
Quic
k Guide
Appendix
A. Func 1 Ctrl No.
(Assign Function 1 Control Number)
A. Func 2 Ctrl No.
(Assign Function 2 Control Number)
Determines the Control Change number generated when you use an ASSIGNABLE FUNCTION [1]/
[2] button on the MOTIF-RACK XS Editor or an external device connected to the MOTIF-RACK XS.
Settings:
off, 1 – 95
BC Ctrl No.
(Breath Controller Control Number)
Determines the Control Change number generated when you use a Breath Controller on an external
device connected to the MOTIF-RACK XS.
Settings:
off, 1 – 95
Arp Sw Ctrl No.
(Arpeggio Switch Control Number)
Determines the Control Number that controls on/off for Arpeggio playback.
Settings:
off, 1 – 95
Arp Hold Ctrl No.
(Arpeggio Hold Control Number)
Determines the Control Number that controls on/off for the Arp Hold parameter in the Arp Edit
display (page 66).
Settings:
off, 1 – 95
Arp 1 – 5 Ctrl No.
(Arpeggio 1 – 5 Control Number)
Determines the Control Number for switching among Arpeggios 1 – 5, stored to each Voice/Multi.
Settings:
off, 1 – 95
Arp Assign Mode
(Arpeggio Assign Mode)
Determines the mode for switching among Arpeggios 1 – 5, stored to each Voice/ Multi.
Settings:
inc, direct
inc.......................... Each time the MOTIF-RACK XS receives a message via the selected Control Change number,
Arpeggios 1 – 5 can be switched. The actual Control Change data value does not matter.
direct ..................... You can select the Arpeggio corresponding to the value of the selected Control Change number: 0 – 25
(Arpeggio 1), 26 – 50 (Arpeggio 2), 51 – 76 (Arpeggio 3), 77 – 101 (Arpeggio 4), 102 – 127 (Arpeggio 5)
3
Micro Tune (User Micro Tuning)
From this window, you can create your original Micro Tuning in the User Bank. Tuning one octave will affect the notes of all octaves from
C -2 to G8.
Number
(Micro Tuning Number)
Determines 1-4Parts” to which the created Micro Tuning setting is stored.
Settings:
1 – 8
Name
(Micro Tuning Name)
Enters the desired name for the Micro Tuning. When the cursor is located here, pressing the
[ENTER] button or the Encoder knob calls up the Naming dialog, where you can enter the desired
name. The Micro Tuning name can contain up to 20 characters. For detailed instructions on entering
characters, refer to “Voice/ Multi Name settings (Entering Characters)” in the Quick Guide (page 47).
C – B
(C Tuning Offset – B Tuning Offset)
Lets you tune the individual notes in cents to create your original Micro Tuning.
Settings:
-99 cents – +0 cents – +99 cents
5
Voice MIDI
Determines the MIDI-related parameters. This window is available only when entering Utility from the Voice mode.
Receive Ch
(Basic Receive Channel)
Determines the MIDI receive channel when the MOTIF-RACK XS is set to Voice mode.
Settings:
1 – 16, omni, off
omni....................... When this is selected, all channel messages are received.
n
In the Multi mode, each Part receives MIDI data according to its assigned MIDI receive channel. The receive
channel for each Part can be set in the Voice display of the Receive Ch parameter (page 94). However, when the
“Layer 1 – 4 Parts” parameter of the Utility General display (page 98) is set to “on,” the receive channels of Parts 1
– 4 in the Multi mode are automatically set to the same value as this Receive Ch (Basic Receive Channel)
parameter.
Transmit Ch
(Basic Transmit Channel)
Determines the MIDI channel over which the MOTIF-RACK XS sends MIDI data generated by
operating Knobs 1
–
5 (to an external sequencer, tone generator, or other device). This parameter is
available in the Voice mode.
Settings:
1 – 16, off
Arp MIDI Out Sw
(Arpeggio MIDI Output Switch)
Determines whether Arpeggio playback data in the Voice mode is output to the external devices as
MIDI messages. When this is set to on, the data is output.
Settings:
off, on
Arp Transmit Ch
(Arpeggio Transmit Channel)
Determines the MIDI transmit channel through which Arpeggio playback data will be sent to the
external devices as MIDI messages. (When the Switch parameter above is set to on.)
Settings:
1 – 16
6
Voice mLAN
Determines various parameters of the Audio Input signal sent from the mLAN terminal in the Voice mode, such as Output jacks, Volume,
Pan, and Effect depth. Keep in mind this applies only when an optional mLAN16E2 has been installed. This window is available only when
entering Utility from the Voice mode. The parameters are the same as those in the mLAN In display in Multi Common Edit (page 91).
7
Voice MEF
Determines Master Effect parameters in the Voice mode. The settings here affect all Voices. This window is available only when entering
Utility from the Voice mode.
