Yamaha MO6, Owner'S Manual

Page: 217 / 240

Master Edit mode Zone Edit
217
Owner’s Manual
V
oice mode
P
erf
ormance
mode
Song mode
Utility mode
File mode
Master mode
P
attern mode
Mixing V
oice
mode
Ref
erence
[F3] TX SW (Transmit Switch)
From this display you can set how the playing of each individual Zone affects transmission of various MIDI messages, such as Control Change and Program
Change messages. When the relevant parameter is set to “on,” playing the selected Zone will transmit the corresponding MIDI messages.
Note that two different display types are provided (see below). Each display type features the same settings in a different format; use the type you feel most
comfortable with.
• Display showing four Zones
• Display showing all parameters for one Zone
Keep in mind that since all the available parameters cannot be simultaneously displayed in the four-Zone display, you will need to use the cursor controls to
scroll the display in order to see and set the other parameters.
Settings:
Bank (TG) Determines whether or not to transmit Bank Select MSB/LSB messages to the internal tone generator.
PC (TG) Determines whether or not to transmit Program Change messages to the internal tone generator.
Bank (MIDI) Determines whether or not to transmit Bank Select MSB/LSB messages to the external tone generator via MIDI.
PC (MIDI) Determines whether or not to transmit Program Change messages to the external tone generator via MIDI.
PB (Pitch Bend) Determines whether or not to transmit Pitch Bend messages to the internal and external tone generator.
MW (Modulation Wheel) Determines whether or not to transmit MIDI messages generated by using the Modulation Wheel to the internal
and external tone generator.
Vol (Volume) Determines whether or not to transmit Volume messages to the internal and external tone generator.
Pan Determines whether or not to transmit Pan messages to the internal and external tone generator.
Slider Determines whether or not to transmit MIDI messages generated by using the Sliders to the internal and
external tone generator.
FC1 (Foot Controller1) Determines whether or not to transmit MIDI messages generated by pressing the optional Foot Controller to the
internal and external tone generator.
FS (Footswitch) Determines whether or not to transmit MIDI messages generated by pressing the Footswitch connected to the
FOOT SWITCH jack to the internal and external tone generator.
Knob Determines whether or not to transmit MIDI messages generated by using the Knobs to the internal and
external tone generator.
[F4] PRESET
From this display you can make the Voice-related settings for each Zone, in the selected Master
program number. In this way, selecting a different Master automatically calls up a completely
different set of Voices and Voice-related settings for the four Zones.
n
Using the [F6] SEND button, you can select whether the settings in PRESET display are immediately
applied or not.
If the [F6] SEND button is turned on (
), each MIDI messages will be output from the MO as
soon as you changed each parameter in this display.
If the [F6] SEND button is turned off (
), each MIDI messages will be output from the MO after
you store the edited Master and then select the Master again.
However, the parameters set to off in the [F1] TRANS or [F3]TX SW display cannot be output.
BankMSB,
BankLSB,
PgmChange (Program Change) Determines the Voice assignment for each Zone in the selected Master.
Settings: Refer to the Voice List in the separate Data List booklet.
Volume Determines the output level of the Voice in each Zone.
Settings:
0 – 127
Pan Determines the stereo pan position of the Voice in each Zone.
Settings: L64 (Left) – C (Center) – R63 (Right)
[F5] KN/CS (Knob/Control Slider)
From this display you can determine which Control Change numbers are used for the Knobs and Sliders for each Zone. These settings are available only
when the Knob/Slider parameter (in the [F2] OTHER display in Common Edit) is set to “zone.”
Settings: off, 1 – 95