background image

NOTE

Thank you for choosing this Yamaha product. 

Please read this manual carefully before using it in a speaker installation. 

Keep the manual in safe place for future reference.

Package Contents

HAF3-3115(W)

❒ 

3-1186 

Angle indicator plates (2 pcs.)

❒ 

3-1201 

Suspension plates (2 pcs.)

❒ 

3-1204 

Rear Joiner plates (2 pcs.)

❒ 

3-0235 

M10-40mm button head socket  

 

screws (14 pcs.)

❒ 

2-1432 

M10 flat washers (16 pcs.)

❒ 

3-0112 

M10 L-key wrench (1 pc.)

• Use only the eye bolts included with the speaker unit.
• For information on load limits and the strength of the eyebolt, refer to the 

owner's manual of the speaker.

• The load limits and strength of the suspension plate are 114.5 kg 

(maximum).

Installation Instructions

1.

 

Flip the speakers upside down. Remove the existing 
speaker screws.

2.

 

Determine the splay angle of the speaker and the holes to 
use on the front joiner plate.

3.

 

Install a rear joiner plate on the rear inserts of the cluster 
with the provided screws and flat washers. Install two angle 
indicator plates on the front inserts using the corresponding 
holes for the appropriate splay angles with the screws and 
flat washers. Tighten permanently.

4.

 

Carefully flip the assembly to expose the top of the 
speakers.

5.

 

Install a rear joiner plate on the rear inserts of the speaker 
using two M10 eye bolts and washers on the side speakers. 
Use the slot closer to the center hole as shown in the 
illustration. Install an M10 screw and washer on the center 
speaker. Tighten permanently.

6.

 

Install two suspension plates on the front inserts of the 
speakers using the same holes as the angle indicator 
plates. Make sure to match the hole positions on the bottom 
and top suspension plates.

7.

 

Use the two eye bolts on the rear and the front to suspend 
the speaker cluster assembly.

8.

 

For steep tilt angles, move the rear eye bolts to the rear 
bottom insert of the speaker cluster and use as a pull back 
point. Make sure to replace the eye bolts with the provided 
screws and washers.

NOTE

Dimensions

HAF3-3115(W)

ARRAY FRAME

Owner’s Manual

EN

PRECAUTIONS

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device  
or other property. These precautions include, but are not limited to, the following:

• Before doing any installation or construction work, consult with an installation expert.

• Make sure that the surface this bracket is being mounted on has the strength to handle the weight of both the speaker and this 

bracket.

• Use bolts and nuts as well as washers for installation and tighten them firmly so that the speaker is secure and does not move.

• Always loosen the corresponding screw before adjusting the angle or direction of the speaker. Never force this adjustment with 

the screw still tightened. 

• Some fittings may deteriorate over extended periods of time due to wear and/or corrosion. For optimum safety, the installation 

should be checked thoroughly at regular intervals.

Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or 
improper installation.

* Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation.

* Company names and product names herein are trademarks or registered trademarks of their respective companies.

* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to 

change  or modify products or specifications at any time without prior notice. Since specifications, equipment or options may  
not be the same in every locale, please check with your Yamaha dealer.

CAUTION

PLEASE READ CAREFULLY BEFORE PROCEEDING 

* Please keep this manual in a safe place for future reference.

3-1186  Angle Indicator Plate

3-1201  Suspension Plate

4.705

.500

φ

.402 3X

1.750

1.175

φ

.402 14X

14.500

7.250

4.750

4.869

1/2-13 TAPPED HOLE

φ

.402 14X

14.500

4.00

Angle Indicator Plate
 (3-1186)[2X]

Suspension Plate
 (3-1201)[2X]

M10 EyeBolt [2X]

M10 Flat Washer [TYP]

Rear Joiner Plate
 (3-1204)[2X]

M10 Screw [TYP]

120

°

120

°

 Maximun Splay Configuration

Tight Pack Configuration

60

°

3-1204  Rear Joiner Plate

28.43

.402 DIA X 30

°

 SLOR

2X

1/2-13 TAPPED HOLE

9.27

Reviews: