Yamaha GRIZZLY 700 FI YFM7FGPX Page 154 Owner'S Manual Download

Page: 154 / 164

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

2065 mm (81.3 in)

Overall width:

1180 mm (46.5 in)

Overall height:

1240 mm (48.8 in)

Seat height:

905 mm (35.6 in)

Wheelbase:

1250 mm (49.2 in)

Ground clearance:

275 mm (10.8 in)

Minimum turning radius:

3200 mm (126 in)

Weight:

With oil and fuel:

294.0 kg (648 lb)

Noise and vibration level:

Noise level (77/311/EEC):

78.8 dB(A) (EUR)

Vibration on seat (EN1032, ISO5008):

Will not exceed 0.5 m/s² (EUR)

Vibration on handlebar (EN1032, ISO5008):

Will not exceed 2.5 m/s² (EUR)

Engine:

Engine type:

Liquid cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

686.0 cm³

Bore

stroke:

102.0

84.0 mm (4.02

3.31 in)

Compression ratio:

9.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

U3B462E0.book Page 1 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands