Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download Page 104

Page: 104 / 164

8-19

2. Install the rear carrier by installing the bolts

and tightening them to the specified torques.

3. Install the seat.

EBU28671

Removing the radiator grills

The radiator grills can be removed to access the
radiator for cleaning.

To remove a radiator grill

Remove the quick fastener, pull the radiator grill
outward at the top, and then pull it upward.

To install a radiator grill

Place the radiator grill in its original position, and
then install the quick fastener.

Tightening torques:

Carrier bolt (upper):

53 Nm (5.3 m·kgf, 38 ft·lbf)

Carrier bolt (lower):

53 Nm (5.3 m·kgf, 38 ft·lbf)

Carrier bolt (under the fenders):

7 Nm (0.7 m·kgf, 5.1 ft·lbf)

1. Radiator grill
2. Quick fastener

U3B462E0.book Page 19 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual, Page: 104 / 164

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews: