manualshive.com logo in svg

Yamaha GRIZZLY 350, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 Owner'S Manual Download Page 106

8-16

8

9. Start the engine, and then let it idle for several

minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.

10. Turn the engine off, wait at least ten minutes,

and then check the oil level and correct it if
necessary.

EBU28572

Final gear oil 

The final gear case must be checked for oil leak-
age before each ride. If any leakage is found, have
a Yamaha dealer check and repair the ATV. In ad-

dition, the final gear oil level must be checked and
the oil changed as follows at the intervals specified
in the periodic maintenance and lubrication chart.

To check the final gear oil level

1. Place the ATV on a level surface.

TIP

The final gear oil level must be checked on a cold
engine.

2. Remove the final gear oil filler bolt, and then

check the oil level in the final gear case.

TIP

The oil level should be at the brim of the filler hole.

1. “CD” specification
2. “ENERGY CONSERVING II”

1

2

U4S212E0.book  Page 16  Thursday, April 17, 2008  9:17 AM

Summary of Contents for GRIZZLY 350







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands